跳转到主内容

简介

Use this guide to replace a cracked or broken screen on your Google Pixel 6 Pro.

Your new replacement screen may come with the fingerprint reader already attached. If not, you will need to reinstall the original fingerprint reader to your new replacement screen and recalibrate the reader to maintain its functionality.

If the frame is deformed, it's important to replace it to make sure the new screen will mount correctly and won’t suffer damage from uneven pressure.

If your battery is swollen, take appropriate precautions. Before disassembling your device, discharge the battery below 25%. This reduces the risk of a dangerous thermal event if the battery is accidentally damaged during the repair.

Note: This guide instructs you to replace only the screen including its safety plastic frame. However, some replacement screens for this phone come without the pre-installed frame (a.k.a. chassis), which requires a different removal procedure. Make sure you have the correct part before starting this guide.

If you do not replace the adhesive seals when reassembling, your device will function normally, but will most likely lose its water protection.

Before you begin this procedure, be sure to have a set of replacement adhesives for both the rear glass and the screen.

  1. Apply a  heated iOpener  to the screen to loosen the adhesive underneath. Apply the iOpener for at least 3 minutes.
    • Apply a heated iOpener to the screen to loosen the adhesive underneath. Apply the iOpener for at least 3 minutes.

    • A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the device.

  2. Once the screen is warm to the touch, apply a suction handle to the bottom edge of the screen. If your screen is badly cracked, covering it with a layer of clear packing tape may allow the suction handle to adhere. Alternatively, very strong tape may be used instead of the suction handle. If all else fails, you can superglue the suction handle to the screen. Lift the screen including its safety frame with the suction handle to create a small gap between the screen and the phone assembly.
    • Once the screen is warm to the touch, apply a suction handle to the bottom edge of the screen.

    • If your screen is badly cracked, covering it with a layer of clear packing tape may allow the suction handle to adhere. Alternatively, very strong tape may be used instead of the suction handle. If all else fails, you can superglue the suction handle to the screen.

    • Lift the screen including its safety frame with the suction handle to create a small gap between the screen and the phone assembly.

    • Insert an opening pick into the gap between the screen frame and the phone assembly.

    • Make sure to insert your opening pick in the right position to avoid separating the screen from its safety frame instead of the phone assembly.

    • Slide the opening pick to the bottom left corner of the screen to slice its adhesive.

    • Leave the opening pick in place to prevent the adhesive from resealing.

  3. Insert a second opening pick at the bottom edge and slide it to the bottom right corner of the screen to slice the adhesive. Leave the opening pick in place to prevent the adhesive from resealing.
    • Insert a second opening pick at the bottom edge and slide it to the bottom right corner of the screen to slice the adhesive.

    • Leave the opening pick in place to prevent the adhesive from resealing.

  4. The screen of the Google Pixel 6 Pro is not only held in place by adhesive but also small plastic pins. In case your opening pick gets blocked during the screen removal procedure it means you insert your pick too deep underneath the screen. Only inserted the tip of the opening pick (~3-4 mm) when slicing the display adhesive. Insert a third opening pick underneath the bottom left corner of the screen. Slide the opening pick along the left edge of the screen to slice the adhesive.
    • The screen of the Google Pixel 6 Pro is not only held in place by adhesive but also small plastic pins. In case your opening pick gets blocked during the screen removal procedure it means you insert your pick too deep underneath the screen. Only inserted the tip of the opening pick (~3-4 mm) when slicing the display adhesive.

    • Insert a third opening pick underneath the bottom left corner of the screen.

    • Slide the opening pick along the left edge of the screen to slice the adhesive.

    • Leave the opening pick in the top left corner to prevent the adhesive from resealing.

  5. If the adhesive becomes hard to cut, it has most likely cooled down. Use your iOpener or heat gun for 1-2 minutes to reheat it. When you slice near the front facing camera, insert only the tip of the opening pick (~2-3 mm) to avoid damaging or smearing the camera.
    • If the adhesive becomes hard to cut, it has most likely cooled down. Use your iOpener or heat gun for 1-2 minutes to reheat it.

    • When you slice near the front facing camera, insert only the tip of the opening pick (~2-3 mm) to avoid damaging or smearing the camera.

    • Insert a fourth opening pick at the top left corner of the screen.

    • Slide the opening pick along the top edge of the phone to slice the adhesive.

    • Leave the opening pick in the top right corner to prevent the adhesive from resealing.

  6. Insert a fifth opening pick and slide it along the right edge of the phone to slice the remaining adhesive. Do not try to remove the display all the way yet, the screen is still connected to the phone assembly.
    • Insert a fifth opening pick and slide it along the right edge of the phone to slice the remaining adhesive.

    • Do not try to remove the display all the way yet, the screen is still connected to the phone assembly.

  7. Avoid straining the display cable during the following procedure. Carefully fold the screen to the left side of the phone assembly like you would open the front cover of a book. Carefully fold the screen to the left side of the phone assembly like you would open the front cover of a book.
    • Avoid straining the display cable during the following procedure.

    • Carefully fold the screen to the left side of the phone assembly like you would open the front cover of a book.

  8. Use a Torx T3 screwdriver to remove the 2.0 mm-long screw securing the display cable metal bracket.
    • Use a Torx T3 screwdriver to remove the 2.0 mm-long screw securing the display cable metal bracket.

  9. Use a pair of tweezers to remove the metal bracket sitting on top of the display cable connector. Use a pair of tweezers to remove the metal bracket sitting on top of the display cable connector.
    • Use a pair of tweezers to remove the metal bracket sitting on top of the display cable connector.

  10. Use a spudger to disconnect the display flex cable by prying the connector straight up from its socket. Use a spudger to disconnect the display flex cable by prying the connector straight up from its socket.
    • Use a spudger to disconnect the display flex cable by prying the connector straight up from its socket.

  11. Remove the screen.
    • Remove the screen.

    • During reassembly, apply new adhesive where it's necessary after cleaning the relevant areas with isopropyl alcohol (>90%).

    • Follow this guide in case you're using a pre-cut adhesive card.

    • During the boot-up process after reassembly, the screen will go through a calibration sequence. Do not touch the screen during this process, as it could result in improper touch calibration and create touch issues.

结论

If possible, turn on your device and test your repair before installing new adhesive and resealing.

To reassemble your device, follow these instructions in reverse order.

The best way to secure the new screen is to apply a sheet of custom-cut double-sided tape to the back of the screen.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

3等其他人完成本指南。

Dominik Schnabelrauch

于2016年11月23日注册

119,306 信誉积分

创作了498篇指南

团队

iFixit iFixit 的会员

Community

145 名成员

创作了17,074篇指南

0条评论

添加评论

浏览统计数据:

过去的24小时: 214

过去的7天: 1,246

过去的30天: 4,717

总计 7,030