一段时间内的信誉积分
信誉积分分解
| 活动 | 计算 | Delta |
|---|---|---|
| 有人完成了你的指南 | 772 | 10762 |
| 管理员通过了你的指南 | 88 | 9432 |
| 你翻译了一本指南 | 55 | 2676 |
| 有人给你的指南点赞 | 196 | 955 |
| 管理员批准了你的维基 | 14 | 700 |
| 被赞成的帖子包含一个指向你指南的链接 | 28 | 188 |
| 帖子被投票赞成 | 11 | 132 |
| 已接受巡查指南步骤编辑 | 33 | 33 |
| 答案被采纳 | 1 | 30 |
| 分类已被接受 | 51 | 29 |
| 有人给你的指南翻译点赞 | 6 | 17 |
| 已接受巡查指南步骤编辑 | 4 | 4 |
帮助
Dominik Schnabelrauch
@schnabel
Dominik Schnabelrauch
| 24,959 | 信誉积分 |
| 6 | 解决方案 |
| 119 | 指南 |
| 于2016年11月23日注册 | |
iFixit EU Team
团队
-
iFixit
We're just some folks with repair on our minds...
-
iFixit EU Team
The European side of iFixit: Same same only different ;)
-
EU content Team
The content team at iFixit Europe
投票
2
0
Hi jerone1925,
a similar question was asked a little while ago regarding the I inserted the pin in the left bottom microphone. I can let you know that the build of the microphone at the top of the phone, is the same as the one in the pictures you see in the link. I can’t give a guarantee but because of that it’s unlikely that you damaged the microphone or affected the water resistance.
Hi Chris V,
thanks for mentioning. I made the correction.
Hallo Kite fun,
das Teil rechts des Lautsprechers ist der Licht und Näherungssensor (Proximity sensor), das Teil links davon ist ein Mikrofon zur Rauschunterdrückung (noise canceling). Bei dem Mikrofon gilt es zu beachten, dass die meisten Ersatzteile ohne Dichtung geliefert werden und diese übertragen werden muss. Generell solltest du beide Teile im World Wide Web mit etwas stöbern finden können ;)
It isn’t possible to see if there’s an extra plate with gaskets like in the Note 7 or the P20 Pro because of the mid frame plastic, that covers the volume and power buttons. We assume that the pins of the buttons run through a tight fit hole in the frame and there’s possibly a small rubber ring or gasket to guarantee the IP68 rating.
Only the telephoto lens has it.
The loudspeaker sits on top of the USB-C charging port and the SIM/NM card try. You can see it in the last picture bottom left.
Hello Lucas Zhu,
the interior build of the A1708 model is a bit different to this one. Especially the connection of the battery. You can check our guides for the A1708 model for the disconnection procedure. The removal of the display in general, is more or less the same with a few differences (e.g. two instead of 3 coax cables). Although the A1708 is a different model you might be able to remove the display following this guide.
Hello axlduri,
thanks for your feedback. In case you weren’t able to loosen the adhesive beneath the back cover with an iOpener, you can use a heat gun to do so. However the iOpener should do the job and should be applied for at least 2 minutes to the back cover. Repeat this step several times until the adhesive is loose. Additionally the battery sits super tight in the mid frame and it’s nearly impossible to remove it safely, without removing the mid frame. You should never work or pry on batteries with metal tools like a screwdriver. If you accidentally puncture them, they can explode or catch fire. Thats the reason why we advise to remove the mid frame. It’s the safest way to remove the battery.
You can try to reopen the phone and check if the flex cable is plugged in correctly or if any cable is ripped. If you can’t find any damage and all cables are plugged in correctly it’s possibly an issue with the replacement part.
Das ist natürlich richtig und wurde korrigiert!
1 / 3 页
下一页