跳转到主内容

修复你的物品

维修的权力

商店

简介

根据本指南的操作来更换Switch的3.5mm耳机孔和游戏卡槽。

  1. 移除背部外壳上的4颗6.3 mm的Y字形Y00螺丝。
    • 移除背部外壳上的4颗6.3 mm的Y字形Y00螺丝。

    Please be careful with these screws. Your bit will go through them like butter and strip them if you're not careful. Speaking from experience.

    Benjamin Fryar - 回复

    So should I use glasses screws

    iceprincess4445 - 回复

    what happens if you do strip a screw?

    Stephanie C Cusimano - 回复

    I used a Y0 bit instead and it worked better for me not to strip the screws

    Alexander Watson - 回复

    Any suggestions of what you can do if you do strip the screw

    Emma Johnson - 回复

  2. 移除立式支架下的1颗6.1 mm的十字形飞利浦#000螺丝。
    • 移除立式支架下的1颗6.1 mm的十字形飞利浦#000螺丝。

    Mine was no longer than about 1mm.

    Nani - 回复

    Agree. This was a very short screw.

    Paul Swinglehurst - 回复

  3. 移除主机下方的2颗2.7 mm的十字形飞利浦#000螺丝。
    • 移除主机下方的2颗2.7 mm的十字形飞利浦#000螺丝。

    These screws wouldn’t go back in for me for some reason. I was definitely using the right screws as I set them aside step by step as usual. I’m not sure what the problem could have been, I just reassembled without the screws.

    Jason Rivera - 回复

  4. 移除主机顶部的1颗2.7 mm的十字形飞利浦#000螺丝。
    • 移除主机顶部的1颗2.7 mm的十字形飞利浦#000螺丝。

    This one didn’t want to come out on its own, and only came loose when I completed the rest of the steps to remove the rear panel, as I pulled the panel off.

    Matt Silver - 回复

  5. 移除右侧手柄滑轨上的1颗3.8 mm十字形飞利浦#000螺丝。 移除左侧手柄滑轨上的1颗3.8 mm十字形飞利浦#000螺丝。
    • 移除右侧手柄滑轨上的1颗3.8 mm十字形飞利浦#000螺丝。

    • 移除左侧手柄滑轨上的1颗3.8 mm十字形飞利浦#000螺丝。

    Please do not use a JIS #0 bit on this kit. I ended up stripping the screw on my switch and now I won't be able to get inside. You are much more likely to remove this screw with a JIS #000 bit, like literally every other screw on this machine. Why I thought I should throughly read and follow the instructions is beyond me, because I guess this ifixit guy decided it would be a great meme to get people to ruin their switches.

    Jacob Klinkenberg - 回复

    +1, JIS #0 seems way too large; I used a #00 and that worked. I agree that #000 might have worked even better, but I saw this comment too late.

    Nikolai Knopp -

    Mine was #000 too. #0 was definitely too large. Also there are signs of blue threadlock.

    Nani - 回复

    tried using #000 and #00 but the screw wont turn, any ideas why

    thawdon - 回复

    Ive been trying to unscrew with the correct 000 bit for like 5 minutes and it wont unscrew :/ please help asap

    xenomorphic/dark Mewtwo - 回复

    this screw stripped in like two seconds using the screwdriver included with ifixit’s kit!

    Connor Martini - 回复

    One screw didn’t come off and now it is stripped…. I’m trapped in this step, desperate and questioning all my life choices…….

    ninja android - 回复

    RIP screw RIP repair

    Moritz Boch - 回复

    RIP crew, RIP repair

    Moritz Boch - 回复

    Well this sucks, I can’t get these %#*@ joy con screws out, why did I spend all this money, its works on every other screw on the joy con rails but its like these middle screws aren’t cut deep enough for anything to grab onto it.

    I got them out with a #000 but it took an obscene amount of pressure put down on the screw. Needless to say I’m not putting them back in.

    Eric - 回复

  6. 将外壳从主机上移除。 将外壳从主机上移除。 将外壳从主机上移除。
    • 将外壳从主机上移除。

    You appear to be missing a step. The SD card reader needs to be removed between steps 6 and 7.

    zharin - 回复

    Achtet darauf die Backplate nicht zu kippen, wie es die Bilder vermuten lassen. Ich habe beim nach Hinten klappen ein Plastikgewinde an der Backplate abgebrochen. Aufpassen.

    I think the picture is a bit misleading. I tiltet the plate while I was removing it what resulted in an broken off screwmount.

    Leon Grell - 回复

  7. 移除Micro SD卡槽上的1颗3.1 mm十字形飞利浦螺丝。
    • 移除Micro SD卡槽上的1颗3.1 mm十字形飞利浦螺丝。

  8. 缓慢地垂直提起micro SD卡槽所在的子板,使其从主机上脱离,然后断开连接并移除它。 在重新组装时,对齐子板并轻轻地按压接口上的海绵垫,直到接头发出咔哒声为止。
    • 缓慢地垂直提起micro SD卡槽所在的子板,使其从主机上脱离,然后断开连接并移除它。

    • 在重新组装时,对齐子板并轻轻地按压接口上的海绵垫,直到接头发出咔哒声为止。

    I cant get the card reader to stay connected to the motherboard when trying to reassemble it. Help needed.

    aNtHoNy R - 回复

    Yes. The reverse is not so simple- you can’t see what you’re doing when you attempt to reconnect and it only takes one small error to completely bend the contacts on the connector. Very delicate.

    if you very gently remove the foam pad sticker, you can at least see better how it lines up and can feel your way to a degree… then you can stick the pad back in. The pad seems pretty critical in keeping things in place once reassembled.

    holmzee - 回复

    Tried several times to replace this SD reader module. As mentioned above, the issue is aligning the connectors together. It appears the foam tape is being used to hold the connection in place. (assuming you can make a viable connection) I am rather surprised at this design. In my experience, mylar ribbon cables like this usually slide into a small PC mounted socket. It appears Nintendo went the cheap route here. This design is prone to failure since it does not enable a positive connection - at least from what I can see.

    Bill Little - 回复

    Directions were great and very helpful! Saved time and money doing myself.

    David Ross - 回复

    I found that tightening the screw for the sd reader all the way down caused the original sd reader to not seat correctly.

    Jimmy Le - 回复

    Alors je suis en détresse total . Jai cassé les bouches en or sur le connecteur qui est soudé sur la carte mère.. comment changer cette toute petite pièces, oû la trouver . Cela fais 1 mois que je cherche partout. Sans remplacer la carte mère. Merci pour vos réponses

    Mike Snow - 回复

    I finished the repair and its not recognizing anything. Ive downloaded a couple more games to the hard drive while I was procrastinating the repair, could a desyncronization issue be causing this?

    David Huser - 回复

    I have the new reader plugged in but my nintendo switch wont turn on now.

    Deadlypizzaman - 回复

    try to hold thepower button for a bit it might just be shut down hold the buutton for at least 30 seconds or just wait for it to turn on

    Jorge Rodriguez -

    I found it easier to connect it without the black foam pad so I could see and than add the foam pad over it. It was super easy and I an I 33 Mom doing this for my son. Was well worth the money for the kit saved us almost 100 bucks

    Katherine Harrison - 回复

    The Y screws are horrible. The bit in the took kit only managed to get two of them out. I have a Y0 bit that got the other two out. What a stupid design those are. Kit should include replacement screws and maybe a new foam pad for the SD Card Reader. New SD card module is tricky to get the connection.

    Garrett ewald - 回复

    Foam pad no longer sticky enough to hold down the connector. Is there any place to get a replacement sticky pad or a work around to keep the connection secure?

    Denise Adams - 回复

    Had my son follow this guide to fix his own switch where the ad card reader didn't work. And he did. Great instructions!!!! Thanks a million!

    William Scott - 回复

    The only difficult part of following this guide is connecting the new sd card reader into the poorly designed motherboard connector. Its quite possible the sd card reader that came in the console wasnt broken at all.

    The repair kit works just as advertised and even comes with stickers.

    Matthias_ Links - 回复

  9. 移除屏蔽板上的6颗3.1mm的十字形飞利浦#000螺丝。
    • 移除屏蔽板上的6颗3.1mm的十字形飞利浦#000螺丝。

    Agreed, still missing that step… I don’t have the image that is in your linked screenshot.. but your screenshot doesn’t mention removing a 7th screw anyway. I had my screwdriver underneath trying to pry it open before realizing there was another screw holding it all together.

    beaugalbraith - 回复

    Sorry everyone! The guide was missing a prerequisite guide. The missing SD card steps should be there now.

    Arthur Shi - 回复

  10. 将屏蔽板从主机上移除。 在铜质热管和屏蔽罩之间涂有一层较厚的粉色导热硅脂。为了最好的散热效果,在移除屏蔽罩之后,最好参考我们的散热硅脂更换指南来移除旧的散热硅脂并为其更换合适厚度的硅脂,例如K5 Pro。 在铜质热管和屏蔽罩之间涂有一层较厚的粉色导热硅脂。为了最好的散热效果,在移除屏蔽罩之后,最好参考我们的散热硅脂更换指南来移除旧的散热硅脂并为其更换合适厚度的硅脂,例如K5 Pro。
    • 将屏蔽板从主机上移除。

    • 在铜质热管和屏蔽罩之间涂有一层较厚的粉色导热硅脂。为了最好的散热效果,在移除屏蔽罩之后,最好参考我们的散热硅脂更换指南来移除旧的散热硅脂并为其更换合适厚度的硅脂,例如K5 Pro

    How do you know if the thermal paste needs to be replaced?

    Youji Hong - 回复

    Once you remove a heatsink you must always replace thermal paste even if you had just applied it ( or add a little more) . The reason is that once heat sink is fitted, paste splits around because of pressure and only needed amount will remain. If you remove the heatsink then some paste will move so when installed again there will be spots without paste. Hope this is clear enough. In any case cost of paste is very small compared to work time and value of your equipment…..

    MacTek -

    I’d recommend replacing the thermal compound to ensure that the cooling system works as intended.

    Blake Klein - 回复

    When your switch starts to lag and drop FPS, if you play breath of the wild and it starts to slow down in heavy areas like the forest where you get the master sword, can i use artic mx 4 insted of the pink compound?

    Diego Soto - 回复

    I’d like to know as well if a cpu thermal compound like arctic mx-4 can be used to replace the pink compound

    Adam Stillman - 回复

    No you shouldn't . It will spill around because it is not viscous enough and then there will be no heat transfer. As suggested by author K5 PRO is the most appropriate compound for such cases.

    MacTek -

    Arctic is generally only supposed to be used on bigger heat sinks like a personal computer. Its not nearly as thick or gummy compared to K5 PRO, and you should always use something that’s thicker for smaller project like a Switch/phone/tablet.

    Shawn Christensen -

    I really don’t understand in what areas I should be replacing the thermal paste.

    Do I leave the giant pink glob that’s present on the back plate or replace that as well?

    Or do I only apply it under the heat sink and on the motherboard?

    Nik Terzic - 回复

  11. 在将撬棒的底部伸到白色插头的地下然后向上移动将其从主板上撬下。 在将撬棒的底部伸到白色插头的地下然后向上移动将其从主板上撬下。
    • 在将撬棒的底部伸到白色插头的地下然后向上移动将其从主板上撬下。

    It is possible to just slide the old rail out after this step, and slide in the new one.

    Johny Sanders - 回复

  12. 用干净的指甲向上撬开固定游戏卡读卡器排线的ZIF连接器。 用干净的指甲向上撬开固定游戏卡读卡器排线的ZIF连接器。 用干净的指甲向上撬开固定游戏卡读卡器排线的ZIF连接器。
    • 用干净的指甲向上撬开固定游戏卡读卡器排线的ZIF连接器

  13. 用撬棒较尖的一头缓缓将游戏卡读卡器的排线从插座上移除。 用撬棒较尖的一头缓缓将游戏卡读卡器的排线从插座上移除。 用撬棒较尖的一头缓缓将游戏卡读卡器的排线从插座上移除。
    • 用撬棒较尖的一头缓缓将游戏卡读卡器的排线从插座上移除。

  14. 用飞利浦螺丝刀从耳机孔支架上移除两颗 3.1 mm的螺丝。 用飞利浦螺丝刀从耳机孔支架上移除两颗 3.1 mm的螺丝。
    • 用飞利浦螺丝刀从耳机孔支架上移除两颗 3.1 mm的螺丝。

  15. 移除耳机孔支架。
    • 移除耳机孔支架。

  16. 用飞利浦螺丝刀从耳机孔和游戏卡读卡器子板上移除一颗3.1 mm螺丝。 用飞利浦螺丝刀从耳机孔和游戏卡读卡器子板上移除一颗3.1 mm螺丝。
    • 用飞利浦螺丝刀从耳机孔和游戏卡读卡器子板上移除一颗3.1 mm螺丝。

  17. 使用撬棒的尖端撬起屏幕排线连接口上的黑色小卡扣。 使用撬棒的尖端撬起屏幕排线连接口上的黑色小卡扣。
    • 使用撬棒的尖端撬起屏幕排线连接口上的黑色小卡扣。

  18. 在组装时,为了让耳机孔连接器就位,请先将整个游戏卡槽子板轻轻抬离Switch的顶部,这样就可以使耳机孔连接器与插座对齐。 用撬棒按压连接器直到听到咔哒声表示连接到位。 沿着整个插头的顶部按压,确保排线放置的位置正确,包括热管下的区域。
    • 在组装时,为了让耳机孔连接器就位,请先将整个游戏卡槽子板轻轻抬离Switch的顶部,这样就可以使耳机孔连接器与插座对齐。

    • 用撬棒按压连接器直到听到咔哒声表示连接到位。

    • 沿着整个插头的顶部按压,确保排线放置的位置正确,包括热管下的区域。

  19. 移除耳机孔和游戏卡槽主板上的1颗3.1mm的十字形螺丝。 移除耳机孔和游戏卡槽主板上的1颗3.1mm的十字形螺丝。 移除耳机孔和游戏卡槽主板上的1颗3.1mm的十字形螺丝。
    • 移除耳机孔和游戏卡槽主板上的1颗3.1mm的十字形螺丝。

    Heh heh heh. I stuck my headphones in the jack and lifted it out that way.

    Ally Gator - 回复

结论

若要重新组装设备,请倒序按照本指南操作。

46等其他人完成本指南。

特别感谢这些译者︰

100%

这些翻译人员帮助我们修复这个世界! 想要作出贡献?
开始翻译 ›

Blake Klein

于2017年01月29日注册

55,991 信誉积分

创作了49篇指南

The SD card slot removal wasn’t in the guide, but otherwise spot on. Thanks!

Justin Lowmaster - 回复

Good catch! It’s updated now :)

Blake Klein -

It worked, thanks

Angie Rayos - 回复

After changing the board out, I don’t have touch on the screen, put the original PCB back in the console and i have touch again, so its not that I did any damage to the flexes or ZIF connector. Any one have any ideas?

Griffin - 回复

Hey man, did you ever figure this out? I have the exact same issue. My touchscreen is no longer working.

Uncle Jessy -

Seems there are different kinds of card slots, European, American and Japanese, Installing for example an Eurean version into an American version wil result in a not working touchscreen , i think it`s a software issue as the cardslot had same parts, if anyone finds a workaround please let us know

Eric Boer (De pspdokter) -

Nintendo does not like aftermarket replacement part. Get original second hand and will be ok

mfijak -

After changing the board i tried to insert a card game and i received the 2162-0002 error.

Could be a compatibility problem?

How to solve?

giovanni.sodaro - 回复

Should you be applying a thermal paste when putting the heat sink back on?

andrewskm68 - 回复

I ordered the tools in this guide directly from this page, and somehow ended up with a 1mm flathead instead of a tri-point driver. Looking at my receipt, the flathead is indeed listed, but I didn’t observe that at the time of purchase — it all makes me a bit frustrated, as I have no idea how that happened. I’m attempting to order the correct driver now, but my son is going to be disheartened that he has to wait another week before he gets his Switch back.

zarmanto - 回复

I followed the whole guide, replaced it — and the headphone jack still only plays through one ear! Any ideas?!

Joshua Smith - 回复

After changing game card, the screen has a mind of its own. It is just going crazy, going back and forth between games and just clicking on random things. It works fine intermittently. I have repaired the joy cons and calibrated. It is still happening. Any suggestions?

Rose - 回复

Unfortunately my press fit connecter got damaged while trying to put it back together. Now I cant use cartrigdes. The guide should point out how to put it back together safely.

Ibramoh _ - 回复

error code 2162-0002

an error has occurred.

please press the power button to restart the console. If you are unable to restart hold the power for 12 seconds to turn the console off.

It wont restart or power off. Any advice?

GARRETT MOLDREM - 回复

took it apart again and found i didn’t have step 19 seated all the way. It fired up fine now, but the game card cannot be read, which was the whole point of the replacement.

GARRETT MOLDREM -

ifixit sent me a replacement card reader that worked this time, EXCEPT now no touch screen. SMH.

GARRETT MOLDREM -

I've tried this at least 8 times and it still hasn't worked any suggestions?b

Evan Miller - 回复

I just tried everything, and I got all the problems mentioned, both the touch screen and card reader don’t work. Please help.

Andy Garcia - 回复

Im getting the same issue i was before i changed the reader… (the game card could not be read. please remove and reinsert it.) headphone jack and screen are working fine.

Edward Lima - 回复

Two things-

-it's one thing if the touch screen doesn't work, but if it's going crazy leave the ribbon in step 13 unplugged. That is the touch screen ribbon and unplugged will deactivate it completely.

- be careful not to strip a screw. It happened to me and it sucked to fix.

Samuel Ybarra - 回复

My son's switch volume consistently goes up to max, need to replace the circuit board (power, volume up, volume down) and replace the speakers.

Kody Riggan - 回复

My son's Switch has the issue where music and sound only plays out of the right headphone speaker. Tried it with several pair to verify this. I'm guessing this repair guide is the only option to fix it.

Jamee Powell - 回复

This looks like an awesome guide. I just bought the part, but this looks very helpful. I'll come back to follow the guide and rate further when I'm done.

Kyle Boxer - 回复

Did all The repairs at first I was getting an error code went back and re-did it it started right up but I’m still not able to play the games with the cards

Keaira Johnson - 回复

I’m having the same touchscreen doesn’t work after replacing the game card reader problem others mention. Any fix for this yet?

Matt Campbell - 回复

Is this what I do if the head phone jack broke off in the switch?

drennanb - 回复

Will card slots from old revisions work with new revisions? I disassembled my HAC-001-(01) and its card slot looks different. But it is ejects cartridges immediately and i need to replace it.

Vitaliy Barabutin - 回复

Part replaced now touch screen won’t work & it still won’t play game cards, I feel as though the new part is defective…..

Darcie Lindley - 回复

installed the new one but still have the same card read error.

Manija Medina-Markham - 回复

and touch screen doesn’t work even with old card reader reinstalled

Manija Medina-Markham - 回复

This was an awesome guide. For someone who is not really good with his hands (and really nervous to cut off the kids from their oh so important video games) this was a life saver. Thanks to all who contributed and giving me a way to repair it without having to wait forever or pay someone twice as much to do so. Took about 45 min following step-by-step with shaky hands :) I held my breath while turning it back on and all I have to say is “MARIO KART IS ALIVE (again…)!”

Jason Spencer - 回复

Hey, I have a weird problem with my big Switch, not actually sure if it’s the game slot or something on the motherboard. The game slot doesn’t work, comes up with the standard “Game can’t be read, re-insert…” message. I’ve tried it with Pokemon Let’s Go, Harry Potter, Mario Kart, Mario Odyssey and Gianna Sisters. All these work on my Switch Lite, the Pokemon game was new. The weird thing is: Gianna Sisters gets recognized immediately on the big Switch, loads up fine and I can play it. The other four games give me the error message. I’ve swapped the game slot over from another broken Switch, with no luck, but I am not sure if that game slot is working either. Before I buy another game slot off ebay, do you guys think that it’s the game slot or anything on the mainboard?

Oliver Schulze - 回复

So, to make things weird, it’s definitely not the game card reader. I’ve got a Switch with a broken screen that works in the dock and plays all games fine and took the game card reader out of that one and installed the game card reader from the console that doesn’t want to play games except for Gianna Sisters into the broken screen one. Broken screen one still plays games fine (fixed the screen by now) and the other one still only reads Gianna Sisters.

Oliver Schulze -

The guide was very well put together, I was able to swap out the part, no problems at all. Great job. For those seeking the same resolution I was for my problem: Swapping out the part did not fix my issue. I still receive the same “CardReadError” when inserting any one of my 33 switch games (though, for whatever reason, Monster Hunter works just fine, it’s the only game I own that the switch will read")

I will continue troubleshooting… hopefully get it figured out. If I do, I’ll come back and comment more. If I don’t, this will sadly be the end of the road for Nintendo with me.

Brandon Pruitt - 回复

添加评论

浏览统计数据:

过去的24小时: 86

过去的7天: 659

过去的30天: 2,465

总计 30,912