What is fault 49

Question

Fisher and Paykel Aquasmart Washing Machine

A top-loading washing machine by Fisher&Paykel.

23 个问题查看全部

steve @stevew

声誉积分: 23

1

发帖于: 2017年9月12日

更多选项

What is fault 49

What dose I need a service ,fault 49 mean .

已回答！ 显示答案我也有这个问题

这是一个好问题吗？

是否

得分 1

13条评论

Hi,I have this fault on my fisher and paykel washer. The wiring harness looks fine,I replaced the inlet valve and the fault is still there. Any idea what else it could be?

由 Jamster 完成的 2019年3月4日

I too am in the same situation. would love further guidance

由 gap423 完成的 2020年6月17日

Have you got the solution?

由 danishinnz 完成的 2020年7月3日

I too am in the same position; water pressure there, no visually obvious blockage of the valves, wiring looks fine, resistance is measured but, still get the same fault code.

由 rob_ldk 完成的 2020年9月25日

Hi @rob_ldk

Have you checked that there is voltage be applied to the valve when it needs to be operated?

Be safety aware as the valve operates at mains supply voltage value i.e 120V AC or 240V AC depending on location.

由 jayeff 完成的 2020年9月25日

显示更多的8条评论

添加一条评论

2个答案

已选择的解决方案

oldturkey03 @oldturkey03

声誉积分: 781.5千

1.1千

893

2.3千

发帖于: 2017年9月12日

更多选项

@stevew Error Fault Condition – Water Inlet Valve Fault.

Repair or Check – Unplug the washer from power. Reconnect any non secure wires on the water inlet valve. Replace the wire harness if it is found to be damaged. If the wiring is okay then measure the resistance of the water inlet valves using an ohm meter. If the resistance of each water inlet valve solenoid is not 60 to 62 ohms then replace the complete water inlet valve assembly.

Parts for Replacement – Water Inlet Valve Assembly or Wire Harness from here

这个答案有帮助吗？

是否

得分 4

5条评论:

have replaced the water inlet valve but code is still coming up

由 rgholmes 完成的 2021年5月7日

Resistance of both inlet solenoids are 57.7 ohms - Is that close enough?

由 Bummers 完成的 2022年10月28日

@bummers it should be coming close. Same issues? Code still coming up?

由 oldturkey03 完成的 2022年10月28日

@oldturkey03

Yes, same issues. I tested the voltage to each valve; my multimeter is only showing about 4 volts. Does that indicate a faulty controller board?

由 Bummers 完成的 2022年10月28日

@bummers 4 Volt would not be enough. Yes, it can be the board but check the wires and everything else as well.

由 oldturkey03 完成的 2022年10月29日

添加一条评论

Hi,I have this fault on my fisher and paykel washer. The wiring harness looks fine,I replaced the inlet valve and the fault is still there. Any idea what else it could be? — Jamster
I too am in the same position; water pressure there, no visually obvious blockage of the valves, wiring looks fine, resistance is measured but, still get the same fault code. — rob_ldk
Hi @rob_ldk

Have you checked that there is voltage be applied to the valve when it needs to be operated?

Be safety aware as the valve operates at mains supply voltage value i.e 120V AC or 240V AC depending on location. — jayeff
have replaced the water inlet valve but code is still coming up — rgholmes
Resistance of both inlet solenoids are 57.7 ohms - Is that close enough? — Bummers
@bummers it should be coming close. Same issues? Code still coming up? — oldturkey03
@oldturkey03

Yes, same issues. I tested the voltage to each valve; my multimeter is only showing about 4 volts. Does that indicate a faulty controller board? — Bummers
@bummers 4 Volt would not be enough. Yes, it can be the board but check the wires and everything else as well. — oldturkey03