修复你的物品 社区 商店

iPhone 6 plus 电池更换

注：你正在编辑的一份前提条件指南。你所做的任何更改将影响包括此步骤的5指南。

返回指南
英语
中文
上一步 下一步

正翻译步骤 4

步骤 4
iPhone 6 Plus Battery Replacement: 步骤 0 中的图像 1，3 iPhone 6 Plus Battery Replacement: 步骤 0 中的图像 2，3 iPhone 6 Plus Battery Replacement: 步骤 0 中的图像 3，3

  • Peel back the final battery adhesive tab from the bottom edge of the battery. Gently pull the battery adhesive tab upward and away from the battery, allowing the adhesive strip to slowly slide out from between the battery and the rear case.

  • Place one hand over the battery as the final strip comes out, or it may fling the battery out of the iPhone.

  • Continue pulling until the final strip comes free from the iPhone.

  • If you removed all three adhesive strips successfully, continue to step 24. Otherwise, if the adhesive breaks off underneath the battery and can't be retrieved, apply a few drops of high concentration (over 90%) isopropyl alcohol under the edge of the battery in the area of the broken adhesive strip(s).

  • Wait about one minute for the alcohol solution to weaken the adhesive. Use the flat end of a spudger to gently lift the battery.

  • Don't try to forcefully lever the battery out. If needed, apply a few more drops of alcohol to further weaken the adhesive. Never deform or puncture the battery with your pry tool.

  • Do not pry against the logic board, or you may permanently damage your iPhone. Do not pry under the topmost section of the battery, near the volume up button and mute switch, or you may damage the audio controls cable, which is adhered to the rear case just beneath the battery.

  • For alternative methods to unstick the battery, continue with the next step below.

从电池底部边缘拉出最后一条易拉胶。

向上轻拉易拉胶使其从电池和后盖间慢慢分离出来。

在拉出最后一条易拉胶的同时请将一只手按住电池，否则胶条可能会将电池带离iPhone

继续轻拉易拉胶使其从机身中完全分离出来。

如果你成功将三条易拉胶取出，请跳过以下两步

如果任意一条易拉胶断裂在了电池底部，请继续以下步骤

-[* black] Peel back the final battery adhesive tab from the bottom edge of the battery.
-[* black] Gently pull the battery adhesive tab upward and away from the battery, allowing the adhesive strip to slowly slide out from between the battery and the rear case.
+[* black] Peel back the final battery adhesive tab from the bottom edge of the battery. Gently pull the battery adhesive tab upward and away from the battery, allowing the adhesive strip to slowly slide out from between the battery and the rear case.
[* icon_caution] Place one hand over the battery as the final strip comes out, or it may fling the battery out of the iPhone.
[* black] Continue pulling until the final strip comes free from the iPhone.
- [* black] If you removed all three adhesive strips successfully, ***[guide|29424|skip over the next two steps|stepid=69610]***.
- [* icon_caution] If any of the adhesive strips broke off underneath the battery and could not be retrieved, ***continue with the next step below***.
+[* icon_note] If you removed all three adhesive strips successfully, continue to ***step 24***. Otherwise, if the adhesive breaks off underneath the battery and can't be retrieved, apply a few drops of high concentration (over 90%) isopropyl alcohol under the edge of the battery in the area of the broken adhesive strip(s).
+ [* black] Wait about one minute for the alcohol solution to weaken the adhesive. Use the flat end of a spudger to gently lift the battery.
+ [* icon_caution] Don't try to forcefully lever the battery out. If needed, apply a few more drops of alcohol to further weaken the adhesive. Never deform or puncture the battery with your pry tool.
+ [* icon_caution] ***Do not*** pry against the logic board, or you may permanently damage your iPhone. ***Do not*** pry under the topmost section of the battery, near the volume up button and mute switch, or you may damage the [guide|31183|audio controls cable|stepid=74381|new_window=true], which is adhered to the rear case just beneath the battery.
+[* icon_note] For alternative methods to unstick the battery, ***continue with the next step below***.

您的所有投稿皆享有基于开源创作共享许可协议（CC BY-NC-SA）的著作权利。