加入维修社区 - 创建账户

简介

If the outer casing of your Punkt MP02 is damaged, cracked, or old, you may consider replacing it. Using this guide, you can successfully replace the casing of your phone and keep all other components inside safe. Before you begin, backup important data, and power off the device to ensure no data loss throughout the process.

你所需要的

1. 步骤 1 Battery
  Use a SIM card eject tool to to eject and remove the SIM card tray on the side of the phone.
  编辑
  
  询问修复机器人
  
  添加评论
  
  1024
2. 步骤 2
  The back panel is held on by glue and multiple tabs.
  
  Slide a Jimmy into the seam between the back panel and the chassis.
  
  Slide the Jimmy around the perimeter to release the back panel, with care not to damage the retaining clips.
  
  Clean any old adhesive with a spudger and isopropyl alcohol, then apply new adhesive to the back panel before reinstalling it.
  编辑
  
  询问修复机器人
  
  添加评论
  
  1024
3. 步骤 3
  Use a Phillips screwdriver to remove the two adjacent 3 mm Phillips screws.
  编辑
  
  询问修复机器人
  
  添加评论
  
  1024
4. 步骤 4
  Insert a Jimmy into the seam between the front and back case.
  
  Slide the Jimmy around the perimeter while prying to separate the front and back case.
  编辑
  
  询问修复机器人
  
  添加评论
  
  1024
5. 步骤 5
  Use a spudger to pry up and disconnect the battery press connector.
  
  Make sure to pry under the connector itself and not on the board.
  编辑
  
  询问修复机器人
  
  添加评论
  
  1024
7. 步骤 6
  Gently pry the battery off with the spudger tool.
  
  Take care not to bend, warp, or puncture the battery during removal.
  编辑
  
  询问修复机器人
  
  添加评论
  
  1024
1. 步骤 7 Screen
  Remove the six 3 mm-long Phillips screws located on the board beneath the battery.
  编辑
  
  询问修复机器人
  
  添加评论
  
  1024
2. 步骤 8
  Remove the antenna coaxial connectors on the board with a spudger by gently prying straight up where they are connected on the board.
  编辑
  
  询问修复机器人
  
  添加评论
  
  1024
3. 步骤 9
  Flip up the two black locking flaps securing each of the two ribbon cables.
  
  Disconnect the two ribbon cables.
  编辑
  
  询问修复机器人
  
  添加评论
  
  1024
4. 步骤 10
  Using your thumbs, push the board up so that the clip can slide out of the indent.
  
  Use a spudger to gently separate the boards.
  
  Ensure that the antennae slide through the holes—do not accidentally pull these off.
  编辑
  
  询问修复机器人
  
  添加评论
  
  1024
5. 步骤 11
  Use a spudger to lift and disconnect the screen press connector.
  
  Make sure to pry up on the edge of the connector, not the board itself.
  
  Remove the screen.
  编辑
  
  询问修复机器人
  
  添加评论
  
  1024
1. 步骤 12 Keyboard Membrane
  Remove the 3 (3mm) Phillips head screws from the board.
  编辑
  
  询问修复机器人
  
  添加评论
  
  1024
2. 步骤 13
  Use a spudger to gently pry the board up and remove it.
  编辑
  
  询问修复机器人
  
  添加评论
  
  1024
3. 步骤 14
  Peel the keyboard membrane off the phone casing.
  编辑
  
  询问修复机器人
  
  添加评论
  
  1024
1. 步骤 15 Casing
  Remove the speaker from the top of the back phone casing using the spudger tool.
  
  You are now be left with both empty casing pieces.
  编辑
  
  询问修复机器人
  
  添加评论
  
  1024

结论

To reassemble your device, follow the above steps in reverse order.
Take your e-waste to an R2 or e-Stewards certified recycler.
Repair didn’t go as planned? Try some basic troubleshooting or ask our Answers community for help.

取消：我没有完成这个指南。