Conair Infiniti Pro Model 259NP Hot/Cold Button Replacement - iFixit 维修指南

加入维修社区 - 创建账户

简介

For sticky cold/hold buttons, you may only need to clean the button. This guide will show you how to fully remove and replace the button.

Note: This guide requires soldering skills. If you don't know how to solder or want to brush up on your skills check out this handy tutorial.

你所需要的

1. 步骤 1 Back Panel
  Caution: Unplug the hair dryer before attempting this guide. Leaving the device plugged in may result in electrocution and damage to the device.
  
  Hold the hair dryer by the handle so that the back panel faces up.
  翻译
  
  询问修复机器人
  
  添加评论
  
  1024
2. 步骤 2
  Remove the two 15.875 mm Phillips #2 screws from the back panel.
  翻译
  
  询问修复机器人
  
  添加评论
  
  1024
3. 步骤 3
  Starting from where the cord attaches to the handle, pull apart the two plastic panels.
  
  Continue separating the back panel, working along the seam.
  
  With moderate force, completely remove the back panel from the hair dryer.
  翻译
  
  询问修复机器人
  
  添加评论
  
  1024
1. 步骤 4 Fan Motor Assembly
  Hold the hair dryer by the nozzle so that the handle points to the left.
  
  Remove the two 1-inch Phillips #2 screws from the back of the fan motor.
  翻译
  
  询问修复机器人
  
  添加评论
  
  1024
2. 步骤 5
  Caution: If you recently used the hair dryer, wait at least 10 minutes before attempting this step. The heating element may still be very hot and can cause serious burns.
  
  Pull on the back of the fan motor to gently lift the motor out of the hair dryer.
  
  Lift the attached electrical wiring and heat shield completely out of the hair dryer.
  翻译
  
  询问修复机器人
  
  添加评论
  
  1024
1. 步骤 6 Hot/Cold Button
  Caution: Do not attempt to open or tamper with the capacitor. You may suffer severe electrical shocks.
  
  Hold the electrical switches so that the wires are facing upwards.
  翻译
  
  询问修复机器人
  
  添加评论
  
  1024
2. 步骤 7
  Focus on the middle of the three buttons.
  
  Desolder the button at the circled locations.
  
  To reattach the new button, resolder at the same points. Be sure the wires connect to the correct locations.
  翻译
  
  询问修复机器人
  
  添加评论
  
  1024

结论

To reassemble your device, follow these instructions in reverse order.

取消：我没有完成这个指南。

2等其他人完成本指南。

作者

与1其他贡献者

Timothy Lo

于04/22/14注册

1,214 声望

创作了7篇指南

+ 12更多徽章

团队

Cal Poly, Team 10-58, Amido Spring 2014 Cal Poly, Team 10-58, Amido Spring 2014 的会员

CPSU-AMIDO-S14S10G58

4 名成员

创作了14篇指南

2指南评论

so where do you buy parts???

akatser1 - 2017年2月15日回复分享

That's not a capacitor, that's an ion generator like this one https://www.goldmine-elec-products.com/p...

Shannon Carey - 2019年9月7日回复分享

浏览统计数据:

过去 24 小时： 3

过去 7 天： 11

过去 30 天： 54

总计 5,311