简介

If the base station is not sending out a signal, the Wi-Fi card may need to be replaced.

  1. First start by peeling off the outer rubbery covering on the bottom of the device.
    • First start by peeling off the outer rubbery covering on the bottom of the device.

    • CAUTION: This part is very fragile, so it is recommended that a blow dryer is used on the covering to heat it up. Simply blow dry the covering while slowly peeling it away, and the covering will not tear.

  2. After removing the rubber covering, unscrew the five 4.9mm Phillips screws in the holes of the plastic casing.
    • After removing the rubber covering, unscrew the five 4.9mm Phillips screws in the holes of the plastic casing.

  3. After unscrewing all five screws, remove the plastic casing. The back should now look like the picture shown.
    • After unscrewing all five screws, remove the plastic casing. The back should now look like the picture shown.

  4. 所有超过US$100.00或包含 Pro Tech工具包的订单免费送货!

    浏览我们的商店

    善于维修,即天赋异禀。

    与 #ImAGenius 分享您的维修故事

    我们都是天才

    与 #ImAGenius 分享您的维修故事

  5. The inner metal casing is latched inside the outer white plastic shell, so insert a pry tool underneath the metal casing and pry it apart from the shell. It should make a click when it comes apart. It should make a click when it comes apart.
    • The inner metal casing is latched inside the outer white plastic shell, so insert a pry tool underneath the metal casing and pry it apart from the shell.

    • It should make a click when it comes apart.

  6. Remove the outer casing.
    • Remove the outer casing.

    • The exposed logic board should look like this.

  7. Take the device out of the casing and orient it so that you can see the WiFi card.
    • Take the device out of the casing and orient it so that you can see the WiFi card.

  8. Wires come from the three antennas and connect on the outer edge of the WiFi card.
    • Wires come from the three antennas and connect on the outer edge of the WiFi card.

    • Carefully pull up on the end of one of the wires to disconnect it from the motherboard.

    • Do this for the remaining two wires.

  9. There are two clips attached to the upper and lower ends of the WiFi card
    • There are two clips attached to the upper and lower ends of the WiFi card

    • CAUTION: For the following step, do not pull the clip after you have detached it. The clip is fragile and too much force may cause the clip to break.

    • Grab the end of one of the clips and pull away from the WiFi card. This should make the clip visibly detached from the WiFi card.

    • Do the same for the other clip.

  10. Grasp the upper and lower ends of the WiFi card. Carefully pull the WiFi card to the right.
    • Grasp the upper and lower ends of the WiFi card.

    • Carefully pull the WiFi card to the right.

    • CAUTION: Do not pull UP (towards yourself) on the WiFi card when removing. The card is on a track that only allows it to move left and right. Forcing the card to move in other directions may result in breaking the track.

    • Completely remove the WiFi card.

结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

Daniel Wagstaffe

于2012年04月02日注册

79 信誉积分

撰写一个指南

团队

Cal Poly, Team 5-2, Forte Spring 2012 Cal Poly, Team 5-2, Forte Spring 2012 的会员

CPSU-FORTE-S12S5G2

5 名成员

创作了6篇指南

浏览统计数据:

过去的24小时: 2

过去的7天: 6

过去的30天: 20

总计 7,507