跳转到主内容

简介

The RAM on a computer is used to store temporary information for your computer to run swiftly. If you computer seems to studder or slow down it might mean that you could use an upgrade of the RAM. RAM upgrades are one of the more common upgrades in a computer unit. You should read through the entire guide before performing the repair and should have all necessary tools readily available. You should also find a safe location to store the various screws taken out of the computer to ensure that they do not get mixed up or lost.

配件

没有特定配件。

  1. Start by removing the battery found on the back of the device.
    • Start by removing the battery found on the back of the device.

    • The battery must be removed in order to ensure the device does not have power! Make sure you do not skip this step!

  2. Using plastic opening tools press down the 6 clips located around the keyboard. Using plastic opening tools press down the 6 clips located around the keyboard.
    • Using plastic opening tools press down the 6 clips located around the keyboard.

  3. Using a plastic opening tool  or spudger move the keyboard out of position. There is a thin cable on the backside of the keyboard. Make sure when you move the keyboard out of position you do so slowly to prevent damage to this cable. If you use a spudger it is recommended that you use a plastic spudger to reduce the chance of damaging any internal parts.
    • Using a plastic opening tool or spudger move the keyboard out of position.

    • There is a thin cable on the backside of the keyboard. Make sure when you move the keyboard out of position you do so slowly to prevent damage to this cable.

    • If you use a spudger it is recommended that you use a plastic spudger to reduce the chance of damaging any internal parts.

  4. Using a spudger gently push the tab on the port forward then pull out the cable.
    • Using a spudger gently push the tab on the port forward then pull out the cable.

    • Be careful to do so as gently as possible. You do not want to damage the port.

  5. Unscrew seven 1.2 mm Phillips #1 screws from the back of the device Unscrew seven 1.2 mm Phillips #1 screws from the back of the device
    • Unscrew seven 1.2 mm Phillips #1 screws from the back of the device

  6. Unscrew eight more 1.2 mm Phillips #1 screws from the front of the computer. Unscrew eight more 1.2 mm Phillips #1 screws from the front of the computer.
    • Unscrew eight more 1.2 mm Phillips #1 screws from the front of the computer.

  7. Using a spudger carefully push though the hole to dislodge the panel on the back of the device then remove the panel by hand. It is recommended that you use a plastic spudger to reduce the chance of damaging any internal parts. It is recommended that you use a plastic spudger to reduce the chance of damaging any internal parts.
    • Using a spudger carefully push though the hole to dislodge the panel on the back of the device then remove the panel by hand.

    • It is recommended that you use a plastic spudger to reduce the chance of damaging any internal parts.

  8. Using your hands pull apart the two clips holding the RAM in then pull out the RAM. It uses (DDR3) 204pin PC3-10600 1333MHz DDR3 SO-DIMM Memory Modules It uses (DDR3) 204pin PC3-10600 1333MHz DDR3 SO-DIMM Memory Modules
    • Using your hands pull apart the two clips holding the RAM in then pull out the RAM.

    • It uses (DDR3) 204pin PC3-10600 1333MHz DDR3 SO-DIMM Memory Modules

结论

To reassemble your device, follow these instructions in reverse order.

7等其他人完成本指南。

Brian

于2016年03月19日注册

1,048 信誉积分

创作了5篇指南

团队

UMass Dartmouth, Team 16-8, Bhusal Spring 2016 UMass Dartmouth, Team 16-8, Bhusal Spring 2016 的会员

UMASSD-BHUSAL-S16S16G8

2 名成员

创作了10篇指南

添加评论

浏览统计数据:

过去的24小时: 2

过去的7天: 10

过去的30天: 58

总计 2,035