修复你的物品 社区 商店

Televisions made by the Chinese multinational electronics company, TCL.

264 个问题 查看全部

更多选项

TCL 55S401issues: from dark, to glitches to now topsy-turvy screen

A year ago this unit went darker on left side of screen; like a black blotch floating across screen. Left unplugged for a few days and problem went away.

This past June, this started:

. Went away after few days and unit remained stable until last week when this started occurring:

Block Image

. Lower half of screen displays flip/mirrored mirrored image along with while screen being darker.

Is it t-con or main board related? Any input appreciated. TIA

回答此问题 我也有这个问题

这是一个好问题吗？

是 否
得分 0

1条评论:

Just an update. TV ran fine since last post, then earlier this week glitched as previously described for a few moments then ran stable. Today after a few hours of viewing problems came back and remained. Swapped t-con and so far so good.

由完成的

添加一条评论

2个答案

筛选条件:
最有帮助的 最新 最老的

更多选项

It's possible that some components are aging or rusting leaving it off few a few months allowed it to return to normal but returned when electrical charge flowed through components. Should be a tcon problem as it is still displaying. Possibly solder points coming loose.

这个答案有帮助吗？

是 否
得分 0

2条评论:

Thanks for the response. In looking at all the boards I see nothing that jumps out to the eye. I've matched the part numbers at shopjimmy site (ordered complete kit) and will start with t-con board swap.

由完成的

"leaving it off few a few months..."

I should note it wasn't left off for a few months, but just 1 or two days. Then worked flawlessly.

由完成的

添加一条评论

更多选项

@ic1 this is not a T-con board issue. Check your video and watch the fade on the left side. "like a black blotch floating across screen" The T-con board can't do that. You can check the video processor on your main board and see if that gets hot. Also, check all the ribbon cables for corrosion and tears. After that, check the "long, skinny boards" that connect to the LCD panel. Those are the driver (scaler) boards. Check for bad cables, corrosion, tears, burned or missing components. Be careful around those boards. they are not replaceable by a DIY'er and only connect via those "flimsy" ribbon cables.

Try to keep the back cover open and have a fan etc. blow some "colder" air across the boards. See if that keeps the TV either running longer before this comes back or if it makes no difference at all.

这个答案有帮助吗？

是 否
得分 0

3条评论:

That black floating blotch occurred over a year ago when left side of screen wold go dark. It went away and returned earlier this year with that glitching seen in the posted video. Right now, whole screen goes dark after few minutes or hour run time and upside down image takes over whole screen.

I just let it run from cold boot and with normal screen. Few minutes after switching to an HDMI input, dark upside-down image again (note this can occur with no devices connected to the unit).

The VP on main board barely warm, and all cables intact, like new. As for the driver board, I have not pulled off backing on them yet. The ribbon cable from the t-con looks good and right now I'm concerned about pulling them in non-destructive manner. Holding it off till I receive board replacements

由完成的

@ic1 sounds like a plan. Let us know how the new boards work out for you.

由完成的

Parts now in hand, but the TCL, which is off mount and left running without any inputs, is picture perfect. Going to pipe some signals into it, wait for failure, then swap one board at a time to see if it resolves issues.

由完成的

添加一条评论

添加你的答案

ic1 将永远感激不已
浏览统计数据:

过去 24 小时： 0

过去 7 天： 1

过去 30 天： 1

总计 47