Would Sugru work to fill this in?

Question

GameCube Controller

The Nintendo GameCube Controller DOL-003. Released November 2001, compatible with Nintendo GameCube, Nintendo Wii, Nintendo Wii U, and Nintendo Switch. Repair for this device is straightforward and requires only common tools.

46 个问题查看全部

Nick @nick

声誉积分: 88.7千

193

260

144

发帖于: 2020年1月4日

更多选项

Would Sugru work to fill this in?

I have a Wii I explicitly bought to use as a Component Gamecube, due to the cost of actual Gamecube component cables. I may use it for Wii games, but I also didn’t even use the one from 2007 for games most of the time and that was a shared Wii.

The controllers work, but the grips have always been gone as long as I have owned them. I tolerate it, but now I think I’m going to use it enough to justify rebuilding the grips.

I am looking at trying white Sugru or an epoxy stick and matte spray paint to fill this in best I can and make it look flush. Either way, I will need to sand it.

Out of both of these materials, which one would be cheaper to use while still working as a filler? I don’t know what type of plastic they are (iconcepts game fury) but I know clone controllers enough to suspect ABS.

已回答！ 显示答案我也有这个问题

这是一个好问题吗？

是否

得分 1

添加一条评论

1个答案

已选择的解决方案

mayer @mayer

声誉积分: 685.2千

MacHale Enterprises

3.4千

1.1千

2.6千

发帖于: 2020年1月4日

更多选项

I use sugru to fill in small holes but this looks like a job for a clear epoxy plus it would be nice and smooth.

这个答案有帮助吗？

是否

得分 2

4条评论:

Yeah - I figured it looked like an epoxy job. I decided to look into the stick type because of how small one low is - I have attached a photo with an Exacto knife as a reference point. Would have been nice to use Sugru since it doesn't need paint though.

I would need paintable epoxy because I want the controller to pass as much as I can. What I may need to do is tape it over, fill it with epoxy and sand it as needed IF I spill.

由 Nick 完成的 2020年1月4日

Look at the white epoxies, paint comes off. https://www.amazon.com/Pratley-Quickset-...

由 mayer 完成的 2020年1月4日

@mayer I have a original bumper left :-). I can make a mold, use Epoxy to form it and rebuild without messing with the controllers.

由 Nick 完成的 2020年1月4日

Remember that if you are using just standard mold making material, your result will be smaller.

由 mayer 完成的 2020年1月4日

添加一条评论

Yeah - I figured it looked like an epoxy job. I decided to look into the stick type because of how small one low is - I have attached a photo with an Exacto knife as a reference point. Would have been nice to use Sugru since it doesn't need paint though.

I would need paintable epoxy because I want the controller to pass as much as I can. What I may need to do is tape it over, fill it with epoxy and sand it as needed IF I spill. — Nick
Look at the white epoxies, paint comes off. https://www.amazon.com/Pratley-Quickset-... — mayer
@mayer I have a original bumper left :-). I can make a mold, use Epoxy to form it and rebuild without messing with the controllers. — Nick
Remember that if you are using just standard mold making material, your result will be smaller. — mayer

GameCube Controller

Would Sugru work to fill this in?

1个答案

添加你的答案