rdklinc

@rdklinc

rdklinc

33,192	信誉积分
629	解决方案
4	指南
于2009年11月22日注册

Hi! I'm John, and I have a Minneapolis company called RDKL, Inc. (pronounced "roadkill incorporated"). I repair/refurbish Apple laptops that I buy from electronics recyclers, and I sell them wholesale. I also buy broken MacBooks at my site, rdklinc.com. Thanks!

团队

Master Techs

Working to save the public money and time.
RDKL, Inc.

投票

384

我的指南

3rd Party Battery Installation Trick for Misshapen A1181 Batteries

"Jump-Starting" a Dead MacBook Battery by Resetting the SMC

Adjusting Trackpad Button Sensitivity on a MacBook

Fixing the MacBook "Floppy Screen" Loose Screen Issue

已完成的指南

iPad 2 Wi-Fi EMC 2415 Front Panel Replacement

iBook G4 12" 1.33 GHz Optical Drive Replacement

MacBook Core 2 Duo Inverter Cable Replacement

iMac G5 17" Model A1058 Logic Board Replacement

iBook G4 12" 1.33 GHz LCD Replacement

MacBook Pro 15" Core 2 Duo Models A1226 and A1260 Optical Drive Replacement

MacBook Pro 15" Core 2 Duo Model A1211 Lower Case Replacement

问题

How can 2011 Sierra user update to High Sierra now that Mojave is out? 2018年10月03日
Hi All! I should know the answer to this but apparently I don’t: I’ve shipped a lot of 2011 Pros to customers with Sierra, an...
MD101LL/A with no sound behaves unusually 2018年05月18日
Hi All! Got an MD101LL/A with audio icon greyed out, i.e. "no audio devices found". Usually this would be resolved by flippin...
Microphone quiet/muffled when using front-facing video 2015年02月19日
Hi All! What does it mean when the microphone works fine when using the back video camera, but when you switch to the front c...
Strange permanent border around the screen 2014年12月23日
Hi All! I've come across a large quantity of 2011 11" MacBooks Airs, and most of them have a strange line on either the right...
Technique to fix "soft" topcase buttons? 2014年07月29日
Hi All! In my travels repairing A1181s, I've come across dozens of topcases with "soft" buttons -- buttons that do not "click
Backlight is unreliable, behaves intermittently 2014年03月01日
Hello! I have a laptop, serial F8V, that has an intermittent backlight -- sometimes it's not on when the laptop powers on, an...
PRAM Zapping Tool -- What is going on here? 2014年01月09日
Hi All! Someone brought this video to my attention, and I thought I'd post it for discussion. It appears to be a tool for zap...
Is there a cheaper 30-pin screen that will work with A1181s? 2013年06月02日
Hi All! I saw this eBay listing and it made me think of a question: http://www.ebay.com/itm/13-3-LCD-CCFL-Screen-Converter-30...
Garage door closes after opening 2012年12月15日
Hello! Recently my garage door started closing immediately after being opened via the remote or the button inside the garage....
Mac Pro won't wake up from sleep with Mountain Lion 2012年07月29日
Hi! My Mac Pro 2.8GHZ 8-Core Early 2008 won't wake up from sleep mode now that it has Mountain Lion. I have found it asleep a...

1 / 7 页

回复： Why will my MacBook Pro not power up even after replacing the battery? 2017年09月23日
Todd, that is not actually how to reset the SMC on your model laptop. That method only works for early 2009 and older, whereas you have a 2010. This is how it's done (from the Apple website): "1. Shut down your Mac. 2. Using the built-in keyboard, press Shift-Control-Option on the left side of the keyboard, then press the power button at the same time. Hold these keys and the power button for 10 seconds. 3. Press the power button again to turn on your Mac."
回复： Laptop won't turn on for half an hour if turned off 2017年09月13日
Was this laptop behaving correctly when it was in your possession, or was it like this when you got it? If it worked at one point, was there a particular event after which the behavior started? I would remove the battery entirely -- when troubleshooting, it's necessary to eliminate extraneous components, and since it works on battery power, we know it's not the battery. My gut tells me it's a board issue, but as someone who doesn't repair boards, here's what I would do: Verify you get the same behavior with another charger. If this was a 15" machine, I'd verify you have an 85W charger (15" won't power on with 60W), but this is a 13" machine, so that shouldn't be the problem. Once the charger is ruled out, I'd take out the board, eliminate any dust and corrosion you find, and then I would disconnect the DC-in, let the DC-in and board sit separately and disconnected from power for a few hours, and then put the machine back together. Sometimes a DC-in will acquire what I think of as a "bad charge", and disconnec...
回复： MacBook turns of after few seconds during startup 2017年09月12日
You need to determine whether it's a keyboard issue or a board-related issue. Pull the keyboard cable and jump the laptop with the power-on pads on the board. If it stays on, you have a bad keyboard. If it still shuts off, you're likely dealing with a board issue. The fact that "holding a key" allows it to stay on suggests you probably have a bad keyboard with a stuck key. Often in that case, holding in a key can temporarily counteract the effect of the stuck key.
回复： unable to turn on after reaplied thermal paste 2017年09月11日
Thermal paste has nothing to do with whether or not a laptop powers on initially. Way too much paste or no paste can cause overheating, but it should power on at least initially and stay on for a minute no matter how well or badly you applied the paste. Once the board is really hot, it will shut off in less time, i.e. the 5th time you power it on it might shut off in ten seconds, since it's already warmed up. Therefore, the board installation is most likely the culprit. Take the board out and re-install it carefully. Make sure you are using the correct screws in the correct places and nothing is getting shorted. As far as thermal paste, you only need to use a tiny drop the size of the head of a small screw. Any more than that, and the paste will spread too far and conduct heat where it shouldn't go. Make sure the previous paste has been completely removed and cleaned away with alcohol.
回复： Disassembled and reassembled, now my display shows weird colours 2017年09月11日
The particular video defects you describe are usually a result of a bad connection between the video cable and the board. The first thing to try is to re-seat the video cable as securely as you possibly can, and that often resolves the problem. Make sure the cable is fully seated into the connector, and that the clasp is all the way down. You can also clean the video connector and the socket, but be very careful. If none of that does it, it's generally the video cable itself (not the board or the screen panel).
回复： Replaced Logic Board w/ Used, Can't Log In 2016年10月15日
The OS would not normally be linked to your serial number, so I would not expect this to be the situation. Do you happen to have FileValue enabled (encryption)? What indications were you getting that the board was going bad? Is it possible that you aren't typing the password that you think you are, and have a bad key from liquid damage? I would type the password in a visible space just to verify. I would boot the laptop from an external bootable volume, which will allow you to see your internal drive as a secondary drive and get at your data, etc. You can do this by connecting an external drive and powering on with the option key held down, which will display the boot options...I would be curious to see if you do get the boot options and not a padlock (which indicates a firmware lock on the new board). Boards with firmware locks can behave in strange ways, so I would want to rule that out. Another idea is to follow these instructions and create a new admin account: https://discussions.apple.com/thread/432...
回复： What to clean and what not with isopropyl alcohol? liquid spill 2016年10月13日
Don't get liquid on the heatsync unless you plan on re-applying thermal paste. Have you booted to an external drive to see if you can wipe the SSD in Disk Utility and do a fresh install? If the SSD is not visible in that scenario I would re-seat it and try again before resorting to cleaning the entire logic board. And even then, I would examine the entire board for corrosion and just remove the corrosion before I arbitrarily starting scrubbing down the whole thing. (I'm assuming you don't have an ultrasonic cleaner.) Personally I use 99% alcohol. 85% alcohol is 15% water....
回复： MacBook Pro boot, chime, but no video, no backlight, no power led. 2016年10月13日
I would take out the board again and re-assemble, making sure all the connections are secure and that you didn't miss any. But first I'd disconnect the video cable and re-attach it, making sure the latch is in place, because sometimes even a slightly loose video cable will cause no video or no backlight. When it powers up do you see a faint image (shine a flashlight through the Apple symbol from behind)? If you do, then you likely either have a bad screen panel (bad bulb) or a blown backlight fuse on the board. But the fact that the power LED is not working points to bigger issues, which is why removing the board again makes sense. While you have it apart, I would disconnect the DC-in from the board and let the two sit for an hour to discharge...sometimes allowing a "bad charge" to dissipate can cause normal behavior to be restored.
回复： water damage, no sound, very slow, fan keep spinning in high speed 2016年10月10日
Personally I would run both the board and the I/O board through my ultrasonic cleaner. There's probably still gunk/corrosion causing these issues. If the board or I/O board have been damaged, an ultrasonic cleaning won't help, but the first step is to remove the gunk and verify that's not the problem.
回复： Battery did not charge, battery ondicator off, but it power up! 2016年10月10日
Battery issues more often than not are caused by a bad battery. Replace the battery with one that you know is good, and that will tell you the answer -- if it works, the battery was bad, and if it doesn't, you know it's the computer, and we can proceed further at that point.

1 / 63 页

PowerBook G4 Titanium DVI Logic Board Replacement 2017年02月23日

The third screw in from the right (close to the middle of the laptop, by the optical drive bay) needs to remain empty because it will eventually be filled when you attach the lower casing. If you put in a screw as shown in this picture, you will then be unable to put in a screw through the lower casing.

一段时间内的信誉积分

信誉积分分解

活动	计算	Delta
帖子被投票赞成	1682	20184
答案被采纳	443	12398
已接受回答	35	350
管理员通过了你的指南	4	252
有人完成了你的指南	3	84
已删除被举报的评论	1	7
将一条评论标记为不恰当。	1	-2
将一条评论标记为不恰当。	2	-4
帖子被投票否决	2	-12
对一个帖子投反对票	33	-66