简介

iOpener是一种绝缘的保温袋,可以在微波炉中加热,并用于沿着iPad或类似设备的边缘将热量传导到粘合剂。

“”按照这些基本说明开始使用新的(黑色,充满液体的)iOpener。 对于白色固体填充的iOpener,请按照这个指南

有关您的设备和维修的详细说明,请参阅我们的iPad维修指南

配件

无需配件。

  1. 在操作前我们推荐你清空微波炉,在底部的任何讨厌的食物残渣最终都可能粘在iOpener上。
    • 在操作前我们推荐你清空微波炉,在底部的任何讨厌的食物残渣最终都可能粘在iOpener上。

    • 把iOpener放在微波炉中间 。

      • 对于旋转式微波炉:确保盘子可以自由旋转。如果你的iOpener卡住了,它可能会过热并燃烧

  2. 加热iOpener三十秒
    • 加热iOpener三十秒

    • 贯穿整个维修过程,如果iOpener 冷却了,在微波炉中每次重新加热额外的三十秒。

    • 注意在维修过程中不要过度加热iOpener,过热可能会导致iOpener爆炸。

    • 如果出现膨胀千万不要碰iOpener。

    • 如果iOpener中间部分依然烫的没法碰,请等待冷却后再加热,一个加热好的iOpener 应该可以保持热度十分钟

    • 把iOpener从微波炉中拿出来,捏着两边扁平边缘中的一个避免碰到中心热的部分。

    • iOpener会非常烫,所以拿着它的时候千万要小心。必要的时候可以使用烤箱手套。

    • 将iOpener什么都没有的一面完全放置在设备被粘合剂密封,您想加热的一角。 液体将会贴合在表面上,确保完美地加热传导。

    • 让袋子在设备上放置大约90秒然后再尝试打开前面板。

    • 在这个时刻您就可以使用塑料打开工具撬开屏幕。 请确保看到您的设备的具体指南, 了解在哪里和如何做到这一点。

    • 在整个过程中,您将需要重新加热iOpener。 为了防止iOpener过热,请始终等到iOpener已经冷却到足够安全。 不要一次微波iOpener超过三十秒钟。

终点

301等其他人完成本指南。

特别感谢这些译者︰

100%

Leon赵国鑫正在帮助我们修复这个世界! 想要作出贡献?
开始翻译 ›

Andrew Optimus Goldberg

于2009年10月17日注册

398,884 信誉积分

创作了412篇指南

团队

iFixit iFixit 的会员

Community

108 名成员

创作了7,531篇指南

I bought two of these, and I can't get an iPad 2 to open using the iOpener; I'm going to keep trying, but heads up, it's not as easy as 1-2-3. I'll update if I get it to work.

Kevin McCartney - 回复

Step 2 says to wait 5 minutes between reheating, step 4 says to wait 3 minutes.

Also, do you sell the "this is a microwave" stickers? xD

Mark Brown - 回复

Will this tool damage the lcd/ pixels or even the camera/sensor if placed on the edge above those? I need to soften up the adhesive only, not replacing the screen at all. I have a surface pro 4.

allanwl - 回复

A short remark about how much force will then be needed to separate the old battery from the heated adhesive would be helpful. I found that even after I was able to begin the insertion of a plastic card between the battery and the case, it required a great deal of force to push the card further under the battery to complete the separation.

Steven Aigner - 回复

While the iOpener tool kit may be the best solution for some applications it is decidedly NOT the optimal tool for removing and replacing a badly cracked Samsung S7 back. The iOpener was simply unable to get the adhesive hot enough to get it to release. Also, the cracked back did not provide enough uninterrupted surface for the suction cap to maintain enough suction to lift the back after I heated it with a heat gun. Overall an EXTREMELY frustrating experience. I do not fault iFixit for this but there could be a little more nuanced explanation about which applications are the best fit for the kit. Mostly I’d like to send a big effuuu to Samsung and all the other smart phone manufacturers who are systematically locking end user out of their purchases. Setting aside the sealed backs it’s absurd that we spend $700 on a smart phone and then have to spend another $40-60 for a protective case and a screen protector. The is no other consumer good we would put up with this.

Alain - 回复

浏览统计数据:

过去的24小时: 100

过去的7天: 848

过去的30天: 4,178

总计 173,599