简介

This guide shows all the steps leading up to, and including, removing the speaker so that a new one can be installed.

Apply pressure to the back cover and slide it forward towards the camera.
  • Apply pressure to the back cover and slide it forward towards the camera.

  • Lift the back cover off the phone.

添加评论

Holding the phone firmly, use the notches to grip and lift up the battery.
  • Holding the phone firmly, use the notches to grip and lift up the battery.

添加评论

Remove the four 4.45mm screws at the corners of the phone.
  • Remove the four 4.45mm screws at the corners of the phone.

添加评论

Use the plastic opening tool to unhinge the locks around the edges of the phone. Do not worry about the inner components of the phone; they are not connected to this case.
  • Use the plastic opening tool to unhinge the locks around the edges of the phone.

  • Do not worry about the inner components of the phone; they are not connected to this case.

添加评论

Lift the casing off of the phone.
  • Lift the casing off of the phone.

添加评论

With the screws removed, locate the antenna.
  • With the screws removed, locate the antenna.

添加评论

Using a Phillips head screwdriver, remove the 4.50mm screw holding the antenna in place.
  • Using a Phillips head screwdriver, remove the 4.50mm screw holding the antenna in place.

添加评论

Using the plastic opener tool, squeeze gently on the antenna cable connector and lift to remove the connector from its position.
  • Using the plastic opener tool, squeeze gently on the antenna cable connector and lift to remove the connector from its position.

添加评论

Gently lift up on the antenna and remove it from the back of the device.
  • Gently lift up on the antenna and remove it from the back of the device.

添加评论

Remove the two 3.50mm screws connecting the motherboard to the case.
  • Remove the two 3.50mm screws connecting the motherboard to the case.

添加评论

Use the plastic opener tool to detach the three ribbons on the motherboard. Use the plastic opener tool to detach the three ribbons on the motherboard. Use the plastic opener tool to detach the three ribbons on the motherboard.
  • Use the plastic opener tool to detach the three ribbons on the motherboard.

添加评论

Lift out the top right ribbon from its slot on the motherboard.
  • Lift out the top right ribbon from its slot on the motherboard.

添加评论

Use the plastic opener tool to unhinge the the locks on the side of the motherboard connecting it to the front casing. Use the plastic opener tool to unhinge the the locks on the side of the motherboard connecting it to the front casing.
  • Use the plastic opener tool to unhinge the the locks on the side of the motherboard connecting it to the front casing.

添加评论

Lift the motherboard away from the front casing.
  • Lift the motherboard away from the front casing.

添加评论

After removing lifting up on the motherboard, the front casing and center frame should be separated as shown.
  • After removing lifting up on the motherboard, the front casing and center frame should be separated as shown.

添加评论

Using tweezers to grasp the pins of the speaker, gently lift the speaker up out of its setting in the front case.
  • Using tweezers to grasp the pins of the speaker, gently lift the speaker up out of its setting in the front case.

添加评论

结论

To reassemble your device, follow these instructions in reverse order.

Brayton

于2011年10月12日注册

40 信誉积分

创作了4篇指南

团队

Cal Poly, Team 3-13, Regan Fall 2011 Cal Poly, Team 3-13, Regan Fall 2011 的会员

CPSU-REGAN-F11S3G13

4 名成员

创作了16篇指南

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 0

过去的30天: 0

总计 706