简介

Replacement of the motherboard requires removal of a few other components first. See the prerequisite guides before attempting just the motherboard.

  1. Heat the iOpeners in a microwave for 1-2 minutes.
    • Heat the iOpeners in a microwave for 1-2 minutes.

    • The iOpeners will be hot. Use caution and hold the tabs on the ends.

    • Place heated iOpeners on screen edges to heat the adhesive.

    • For more detailed instructions on how to use the iOpeners, please refer to the iOpener Instructions.

    添加评论

  2. Separate the screen assembly from the back by wedging the picks between the two components.
    • Separate the screen assembly from the back by wedging the picks between the two components.

    • Slide the picks along the edge and leave them holding the device open all around the edges.

    添加评论

    • Place suctioning device near the corner of the screen and gently lift up to create a gap between the front panel assembly and the back.

    • Insert the picks to hold the two components apart once a gap is created.

    添加评论

    • Once all edges have been disconnected, carefully lift the screen off by pulling one side up.

    • Be careful not to cut yourself. Any broken glass from the screen will be sharp.

    添加评论

    • Using the tweezers, gently peel up on the silver tape covering the connector.

    添加评论

    • Use the plastic opening tool to get under the connector piece. This will allow you to remove the front panel assembly from the rest of the device.

    添加评论

    • Detach the connecter from the inside of the device.

    • Lift the screen to separate the front panel assembly from the rest of the device.

    添加评论

    • Remove the 17 silver 3.0 mm Phillips head screws located around the edge of the device using the screwdriver.

    • For additional information on how to remove screws, please refer to Screwdriver Best Practices.

    添加评论

    • Remove the 2 centrally-located black 3.0 mm Phillips head screws using the screwdriver.

    添加评论

    • Use the plastic opening tools to gently separate the middle panel from the rest of the device.

    • Move the tool around under the edges until you can remove the panel by hand.

    • Popping/cracking noises are completely normal. These are the sounds of the panel separating from the rest of the device.

    添加评论

    • Lift up the central panel starting from one corner to separate it from the rest of the device.

    • Pull towards the top of the device as you lift out to ensure that the charging port connection is not damaged.

    添加评论

    • Using the screwdriver, remove the 4 black 3.0 mm Phillips head screws located on the upper and lower motherboard.

    添加评论

    • Using the plastic opening tools unlock the 11 connectors that must be undone before the motherboard can be removed.

    添加评论

    • Using the plastic opening tool, continue disconnecting cables on upper motherboard.

    添加评论

    • Continue disconnecting along the left side of the device.

    添加评论

    • Continue removing cables on the lower motherboard.

    添加评论

    • Using tweezers, remove the green plastic film to reach the last cable.

    添加评论

    • Carefully lift the orange flap using the black spudger. Then disconnect the cable from the motherboard.

    添加评论

    • Using the tweezers, gently pull the cable off of the motherboard.

    添加评论

    • Carefully lift the top portion of the motherboard off of the back panel with your hands.

    添加评论

    • Using the tweezers, wiggle under the lower motherboard to remove adhesive.

    • Carefully grab the adhesives with the tweezers and lift up.

    添加评论

    • Gently lift up the lower motherboard.

    • Keep the two portions of the motherboard together. If the connecting cable is damaged, it could further ruin the condition of the board.

    添加评论

    • Remove both pieces of the motherboard carefully from the back panel.

    添加评论

结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

Nash Elder

于2018年04月18日注册

555 信誉积分

创作了4篇指南

团队

Cal Poly, Team S16-G5, Livingston Spring 2018 Cal Poly, Team S16-G5, Livingston Spring 2018 的会员

CPSU-LIVINGSTON-S18S16G5

5 名成员

创作了12篇指南

添加评论

浏览统计数据:

过去的24小时: 6

过去的7天: 32

过去的30天: 117

总计 522