简介

iOpener是一种绝缘的保温袋,可以在微波炉中加热,并用于沿着iPad或类似设备的边缘将热量传导到粘合剂。

“”按照这些基本说明开始使用新的(黑色,充满液体的)iOpener。 对于白色固体填充的iOpener,请按照这个指南

有关您的设备和维修的详细说明,请参阅我们的iPad维修指南

配件

无需配件。

在操作前我们推荐你清空微波炉,在底部的任何讨厌的食物残渣最终都可能粘在iOpener上。
  • 在操作前我们推荐你清空微波炉,在底部的任何讨厌的食物残渣最终都可能粘在iOpener上。

  • 把iOpener放在微波炉中间 。

    • 对于旋转式微波炉:确保盘子可以自由旋转。如果你的iOpener卡住了,它可能会过热并燃烧

which temperature must be used for heating? Thx

fbarletta - 回复

I found you need to be very patient when using the iOpener. It's worth taking your time, giving the heat time to work on the glue. When I finally got the battery out, there were some strips of glue left behind that I just cleaned off with some isopropanol before installing the new battery.

By the way, I had to run the iOpener for longer in my microwave for it to get hot enough. When it was too hot to touch, I figured it was hot enough for the batteries.

Fredrik -

I didn't find this to be as hard as I had built it up in my mind to be; HOWEVER, saying that I need to say years ago I was the local Nokia service center in my town. But many years ago right after they got rid of analog times. Yeah. A classic installer/repairer mistake when starting something they haven't fixed or installed before is picking up the instructions, flipping through them; maybe even reading a section that is new-then tossing the instructions over the shoulder. "I got this." This usually comes right before something major gets broke. And I can tell you when you try to do it yourself and then mess it up horribly then take it to the repair shop. Well we called that "I can do it myself" syndrome and charged extra to put back together what they brought in in the box. Now knowing all this - I can't stress this enough because I am stupid, stupid, stupid. COVER YOUR SCREEN IN CLEAR BOXING TAPE AND READ ALL THE INSTRUCTION BELOW THROUGH TO THE END BEFORE EVEN ATTEMPTING THIS FIX. Take my advise.

windizy - 回复

I didn't have an iOpener, so I used a wheat type heat bag. If you do this though, make sure you put a layer of plastic between your Mac and the bag, or you'll get condensation in places you don't want it.

Martin Gray - 回复

I started out using the iOpener but switched to my wife's hairdryer. A heat gun or hair dryer proved to be much more convenient and is a time saviour. You can heat more and the glue becomes more fluid make the next steps with the opening picks much easier

Jan Van Puymbroeck - 回复

Use a hair dryer! Watch this vid: https://youtu.be/16GkvjVyOJA It is much easier to do if you heat it from the other side.

Fletcher Carpenter - 回复

I wonder how many people actually wrapped in their iPhone into iOpener and put this "sandwich" into microwave??

putinaspiliponis - 回复

I know this is obvious, but backup your iPad with iTunes before you start. I'd also turn off your passcode if you have one.

Laurie Higgins - 回复

Ther first time you heat up the iOpener for this repair when its room temperature I had to heat it up for more than 30 seconds. I remember I had to heat it up for around 45 seconds. However, after that when you need to reheat it again during the repair 30 seconds will be enough.

Yousef Ghalib - 回复

I've been with Samsung for 8 years now!! Never did i have a case on any of my phones My Samsung 8 is 2 months old the case protector around the edge pop off and broke my phone it's like someone put a bullet hole in it

Sherry Carew - 回复

Not everybody has a microwave. You need to state how long and at what temperature in a conventional oven.

Esmond Pitt - 回复

Hi, the microware have multiple power 1 to 9, what must be used ?

Regards,

Cedric

Cedric VINCENT - 回复

加热iOpener三十秒
  • 加热iOpener三十秒

  • 贯穿整个维修过程,如果iOpener 冷却了,在微波炉中每次重新加热额外的三十秒。

  • 注意在维修过程中不要过度加热iOpener,过热可能会导致iOpener爆炸。

  • 如果出现膨胀千万不要碰iOpener。

  • 如果iOpener中间部分依然烫的没法碰,请等待冷却后再加热,一个加热好的iOpener 应该可以保持热度十分钟

May I know the temperate limit about heating iOpener? (maximum 150 degrees Celsius?) thx so much.

yamayhuang - 回复

I had to heat mine up for more than 30 seconds. After 30 seconds on high it was only warm. It had to keep trying different times and checking it until it got hot. I think the initial time that I put it in for was over a minute.

whale13 - 回复

DO NOT USE IN NON ROTATING MICROWAVE! It will pop a hole. I had it in for 45 seconds the first time. It wasn't very hot inside and I saw it started to leak on the paper towel I put under it. Just a fair bit of advice. I think I will just stick with the heat gun. Loud but useful.

Alex Jackson - 回复

I don't own a microwave.

mdanihy - 回复

Its again waterproof when you change iphone 7 battery?

Jon - 回复

I don't have a microwave???

Joe Blow - 回复

30 sec at which equivalent watts setting and what temperature does iOpener heats up to for 30 secs. Only just bought it so needs info before using it. Thanks

Sam Stieg - 回复

can i use just ordinary microwave???

juneseok kwon - 回复

If I don't have a microwave then I try to use hot air gun so how many munuts i want to heat ?

Mohideen Rifay - 回复

I heated mine up for 30 seconds, tested, then again for 30 seconds. It felt adequately hot. Leaving it on the left side, per the instruction, for a minute did not loosen the adhesive. I ended up pulling the suction cup hard enough to shadder the old screen. Moral of the story, I don't think it gets hot enough safely to have an affect.

Travis Dixon - 回复

There is a clear problem here with the heating part using the iopener things....no details are given. Whoever is testing them needs to make it clear - What temperature does it need to be? And for which phone models, because they differ in what's needed. It's only £10-15 for a laser guided temp sensor unit, and the designers/repairers should have one of those already for doing these kinds of repairs. Explaining half a repair, is worse than not explaining at all :-(

assortedrubbish - 回复

I used a hot water bottle, works well as it covers the whole screen and stays hot for longer.

dave - 回复

If I may suggest include your microwave wattage so people can get an idea on time for there own

Patrick Storey - 回复

I ended up using a hair dryer. That iOpener thing took forever.

mark fitzgerald - 回复

30 seconds sure isn’t cutting it… 45 didn’t get the screen of my iPad air 2 to budge either… even after resting on the ipad for 4 minutes.

60 seconds in the microwave, the iOpener burst.

I’ll get a new one and try once more with heating it 45 seconds and repeat that for 30 minutes like others have said here. If that doesn’t work it’ll have to be the heat gun.

K

Karl Marble - 回复

  • 把iOpener从微波炉中拿出来,捏着两边扁平边缘中的一个避免碰到中心热的部分。

  • iOpener会非常烫,所以拿着它的时候千万要小心。必要的时候可以使用烤箱手套。

Will a hair dryer work for heating the glass?

Me berg - 回复

Yes, as does a heat gun.

anonymous 4602 - 回复

I did this repair. I used a hair dryer, I think it works better: gets very hot fast.

Cobus de Beer - 回复

  • 将iOpener什么都没有的一面完全放置在设备被粘合剂密封,您想加热的一角。 液体将会贴合在表面上,确保完美地加热传导。

  • 让袋子在设备上放置大约90秒然后再尝试打开前面板。

  • 在这个时刻您就可以使用塑料打开工具撬开屏幕。 请确保看到您的设备的具体指南, 了解在哪里和如何做到这一点。

  • 在整个过程中,您将需要重新加热iOpener。 为了防止iOpener过热,请始终等到iOpener已经冷却到足够安全。 不要一次微波iOpener超过三十秒钟。

添加评论

终点

284等其他人完成本指南。

特别感谢这些译者︰

100%

Leon赵国鑫正在帮助我们修复这个世界! 想要作出贡献?
开始翻译 ›

Andrew Optimus Goldberg

于2009年10月17日注册

387,249 信誉积分

创作了412篇指南

团队

iFixit iFixit 的会员

Community

111 名成员

创作了6,675篇指南

I bought two of these, and I can't get an iPad 2 to open using the iOpener; I'm going to keep trying, but heads up, it's not as easy as 1-2-3. I'll update if I get it to work.

Kevin McCartney - 回复

Step 2 says to wait 5 minutes between reheating, step 4 says to wait 3 minutes.

Also, do you sell the "this is a microwave" stickers? xD

Mark Brown - 回复

Will this tool damage the lcd/ pixels or even the camera/sensor if placed on the edge above those? I need to soften up the adhesive only, not replacing the screen at all. I have a surface pro 4.

allanwl - 回复

A short remark about how much force will then be needed to separate the old battery from the heated adhesive would be helpful. I found that even after I was able to begin the insertion of a plastic card between the battery and the case, it required a great deal of force to push the card further under the battery to complete the separation.

Steven Aigner - 回复

While the iOpener tool kit may be the best solution for some applications it is decidedly NOT the optimal tool for removing and replacing a badly cracked Samsung S7 back. The iOpener was simply unable to get the adhesive hot enough to get it to release. Also, the cracked back did not provide enough uninterrupted surface for the suction cap to maintain enough suction to lift the back after I heated it with a heat gun. Overall an EXTREMELY frustrating experience. I do not fault iFixit for this but there could be a little more nuanced explanation about which applications are the best fit for the kit. Mostly I’d like to send a big effuuu to Samsung and all the other smart phone manufacturers who are systematically locking end user out of their purchases. Setting aside the sealed backs it’s absurd that we spend $700 on a smart phone and then have to spend another $40-60 for a protective case and a screen protector. The is no other consumer good we would put up with this.

Alain - 回复

I bought two of these, and I can't get an iPad 2 to open using the iOpener; I'm going to keep trying, but heads up, it's not as easy as 1-2-3. I'll update if I get it to work. Also, do you sell the "this is a microwave" stickers? xD Refer: free run 3 online

Martha Wilson - 回复

Thanks Andrew! :-)

Tony - 回复

添加评论

浏览统计数据:

过去的24小时: 146

过去的7天: 862

过去的30天: 3,951

总计 160,451