简介

This guide shows how to replace the camera lens and surrounding mechanisms (including the motor).

配件

无需配件。

Flip camera so you are looking at the bottom.
  • Flip camera so you are looking at the bottom.

  • Unscrew all 5 base plate screws.

添加评论

Lift open retainer clip by sliding the clip to the left and letting the clip pop up.
  • Lift open retainer clip by sliding the clip to the left and letting the clip pop up.

添加评论

  • Unscrew the single screw located next to the battery slot.

添加评论

  • Turn the camera so that the USB, AV and DC in/out rubber plate it facing you.

  • Lift the rubber plate exposing the ports beneath.

添加评论

  • Unscrew the 2 screws next to the USB and AC ports.

添加评论

  • Use a flathead screwdriver or another flat opening tool to pry the faceplate from the whole device.

添加评论

  • Pull off the faceplate to reveal the inside of the camera.

  • Be careful of the connector that goes from the faceplate to the motherboard . Disconnecting this line will cause the camera not not power on through the on/off switch anymore.

添加评论

  • Use a phillips head screwdriver to remove the 3 screws highlighted in the picture.

添加评论

  • Unscrew the 2 screws located on either side of the flash.

添加评论

  • Get a flathead screwdriver or an iPod opening tool (both are shown in this picture).

  • Carefully pry off the blackplate from the remaining part of the camera.

添加评论

  • Pull the backplate off.

添加评论

  • Unscrew the screw shown in the picture from LCD screen.

添加评论

  • Remove the side pannel by sliding it off the body of the camera.

  • Lift the camera no more than 3cm to make sure all screws have been taken off.

添加评论

  • Flip camera so you are looking at the front.

  • Remove gray and blue wiring with tweasers by gently wiggling and pulling.

  • Be careful not to rip the wiring tape with the tweezers.

添加评论

  • Locate the tape securing the wiring with the gray end piece located on top of the camera.

  • Gently lift up on the tape till all wires are exposed.

添加评论

  • Flip Camera to the bottom side as shown.

  • Pull and wriggle the thin yellow wiring tape to detach it from the rest of the camera, while leaving it attached to the LCD screen.

添加评论

  • Flip camera so the front is facing you.

  • Locate speaker in upper right hand corner.

  • Gently lift with tweasers.

  • Feed wiring through designated spot so that it is no longer connected to the camera.

添加评论

  • Lift the LCD screen so the thick yellow wiring is the only thing attaching the LCD screen to the camera.

  • Gently pull the thick yellow wiring out by using the forefinger and thumb.

添加评论

  • Flip camera so you are looking at the back.

  • Remove the 3 screws from the rear of the camera behind the lens.

添加评论

  • Flip camera so the front lens is facing up.

  • Unplug lens from logic board.

添加评论

  • Flip camera over so the lens is facing down and the back of the camera is facing you.

  • Gently pull back on the wire that connects logic board to lens assembly so it is no longer connected.

添加评论

  • Flip camera so the front is facing you.

  • Carefully lift lens assembly out of camera.

添加评论

结论

To reassemble your device, follow these instructions in reverse order.

Joshua

于2010年04月15日注册

7 信誉积分

创作了2篇指南

团队

Cal Poly, Team 28-23, Regan Spring 2010 Cal Poly, Team 28-23, Regan Spring 2010 的会员

CPSU-REGAN-S10S28G23

4 名成员

创作了7篇指南

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 1

过去的30天: 1

总计 2,349