修复你的物品 社区 商店

Linksys WRT54GS v2 Antenna Ports Replacement

简介

You will be desoldering the antenna ports.

你所需要的

  1. Linksys WRT54GS v2 Antenna Ports Replacement, Front Case: 步骤 1 中的图像 1，1

    • Turn the router over so that all four of its feet are facing upwards.

    翻译

  2. Linksys WRT54GS v2 Antenna Ports Replacement: 步骤 2 中的图像 1，1

    • Remove the rubber inserts inside the the two purple feet located on the router's front case.

    • This may be a challenge, so try the following two methods:

    • Use a plastic opening tool. Insert the flat end of the tool into the seam and slowly pry the rubber feet out.

    • Use a metal spudger. Insert the point of the metal spudger directly into the hole of the rubber feet and pry the insert out.

    翻译

  3. Linksys WRT54GS v2 Antenna Ports Replacement: 步骤 3 中的图像 1，1

    • Use a Phillips #2 Screwdriver to remove the two 5.8 mm screws holding the front case to the motherboard.

    翻译

  5. Linksys WRT54GS v2 Antenna Ports Replacement: 步骤 4 中的图像 1，1

    • Squeeze the sides of the router's backcase inward and pull off the purple front case. It is helpful to have a second person assist you for this step.

    翻译

  6. Linksys WRT54GS v2 Antenna Ports Replacement, Motherboard: 步骤 5 中的图像 1，1

    • Slide the board unit out and up.

    翻译

  7. Linksys WRT54GS v2 Antenna Ports Replacement: 步骤 6 中的图像 1，1

    • Flip the circuit board over and use a Phillips #2 Screwdriver to remove the 6.9mm screw holding the board to the back case.

    • Slide the back cover out and away from the circuit board.

    翻译

  8. Linksys WRT54GS v2 Antenna Ports Replacement, Antenna Ports: 步骤 7 中的图像 1，2 Linksys WRT54GS v2 Antenna Ports Replacement, Antenna Ports: 步骤 7 中的图像 2，2

    • Turn the circuit board over and identify which solder connection you will desolder.

    • The solder connections shown in red hold the right antenna port in place. There is one more attachment for this antenna on the other side of the board.

    • The solder connections shown in blue hold the left antenna port in place. Desolder these 4 points to remove the antenna port.

    翻译

  9. Linksys WRT54GS v2 Antenna Ports Replacement: 步骤 8 中的图像 1，1

    • Turn on your soldering iron and allow it to get to its highest temperature setting (minimum 600ºF).

    翻译

  10. Linksys WRT54GS v2 Antenna Ports Replacement: 步骤 9 中的图像 1，1

    • Desolder the connection by following iFixit's guide to repairing soldered connections: 如何焊接和拆焊.

    翻译
结论

To reassemble your device, follow these instructions in reverse order.

2等其他人完成本指南。

作者

与6其他贡献者

Allian Roman

于10/12/11注册

276 声望

创作了5篇指南

徽章: 8

+ 5更多徽章

团队

Cal Poly, Team 3-4, Regan Fall 2011 Cal Poly, Team 3-4, Regan Fall 2011 的会员

CPSU-REGAN-F11S3G4

4 名成员

创作了12篇指南

一条评论

Most do not have removeable antennae ports

tom - 回复

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 1

过去 30 天： 4

总计 3,241