修复你的物品 社区 商店

JBL Charge Speaker Replacement

简介

The speakers are located behind the motherboard. Follow this guide to replace one or both broken speakers.

你所需要的

  1. JBL Charge Speaker Replacement, Disassembling JBL Charge Casing: 步骤 1 中的图像 1，3 JBL Charge Speaker Replacement, Disassembling JBL Charge Casing: 步骤 1 中的图像 2，3 JBL Charge Speaker Replacement, Disassembling JBL Charge Casing: 步骤 1 中的图像 3，3

    • Make sure the device is powered off before you begin to disassemble the speaker.

    • Remove the trim from the speaker using a jimmy or metal spudger.

    翻译

  2. JBL Charge Speaker Replacement: 步骤 2 中的图像 1，2 JBL Charge Speaker Replacement: 步骤 2 中的图像 2，2

    • Use the PH1 screwdriver to remove all five of the 6 mm screws from the battery cover.

    • Remove the battery cover and set the cover aside.

    翻译

  3. JBL Charge Speaker Replacement: 步骤 3 中的图像 1，2 JBL Charge Speaker Replacement: 步骤 3 中的图像 2，2

    • Use a spudger to carefully remove the liquid electrical tape that holds the battery inside the battery compartment.

    • Be careful not to puncture the battery, or damage the battery wire underneath the liquid electrical tape.

    翻译

  4. JBL Charge Speaker Replacement: 步骤 4 中的图像 1，2 JBL Charge Speaker Replacement: 步骤 4 中的图像 2，2

    • Use a spudger to lift the battery out of the device.

    • Lift the end of the battery that does not have the wire connection and remove the 16 mm PH2 screw underneath the battery.

    • Notice the wire that is connecting the battery to the device. Attempting to remove the battery completely could cause damage to the wire. Do not use a metal spudger to remove the battery, this could cause damage.

    翻译

  5. JBL Charge Speaker Replacement: 步骤 5 中的图像 1，2 JBL Charge Speaker Replacement: 步骤 5 中的图像 2，2

    • Remove the four 16 mm screws from the white plastic casing using the PH2 screwdriver.

    翻译

  7. JBL Charge Speaker Replacement: 步骤 6 中的图像 1，2 JBL Charge Speaker Replacement: 步骤 6 中的图像 2，2

    • Starting in a corner of the device where the casing and the side meet, use a pointed metal spudger to pry the back casing off the speaker and the glue holding the seam together.

    • Slide the metal spudger along the seam to separate the back casing from the rest of the speaker.

    翻译

  8. JBL Charge Speaker Replacement: 步骤 7 中的图像 1，2 JBL Charge Speaker Replacement: 步骤 7 中的图像 2，2

    • Once the back casing is open, disconnect the three white connectors from the motherboard.

    • Remove the upper casing.

    翻译

  9. JBL Charge Speaker Replacement, Motherboard: 步骤 8 中的图像 1，1

    • Remove the 9 mm Phillips screw in the corner of the motherboard.

    翻译

  10. JBL Charge Speaker Replacement: 步骤 9 中的图像 1，2 JBL Charge Speaker Replacement: 步骤 9 中的图像 2，2

    • Remove the motherboard from the casing by lifting the corner of the board out of the device.

    • If the motherboard won't budge, be sure that the square component on the bottom of the motherboard clears the edge of the speaker.

    • During reassembly, make sure the motherboard is fully installed and not sticking up past its original position, as this could damage the motherboard.

    翻译

  11. JBL Charge Speaker Replacement: 步骤 10 中的图像 1，1

    • Disconnect the two white connectors from the bottom of the motherboard.

    翻译

  12. JBL Charge Speaker Replacement: 步骤 11 中的图像 1，2 JBL Charge Speaker Replacement: 步骤 11 中的图像 2，2

    • Pull down on the black clip holding the ribbon cable in place.

    • Pull the ribbon cable from the connector using the blue tab.

    • Remove the motherboard from the device.

    翻译

  13. JBL Charge Speaker Replacement, Speaker: 步骤 12 中的图像 1，1

    • Using the PH1 screwdriver, remove the 9mm Phillips screw that connects the black tube to the device's interior.

    翻译

  14. JBL Charge Speaker Replacement: 步骤 13 中的图像 1，2 JBL Charge Speaker Replacement: 步骤 13 中的图像 2，2

    • Slowly but firmly pull the grey cap off the device. This will provide complete access to the speakers.

    翻译

  15. JBL Charge Speaker Replacement: 步骤 14 中的图像 1，2 JBL Charge Speaker Replacement: 步骤 14 中的图像 2，2

    • Each speaker is held in place with two 9mm Phillips screws. Remove the screws using the PH1 screwdriver head.

    • If you are replacing the left speaker, remove the screws and speaker on your right.

    • If you are replacing the right speaker, remove the screws and speaker on your left.

    翻译

  16. JBL Charge Speaker Replacement: 步骤 15 中的图像 1，1

    • Pull the speaker out of the casing.

    翻译
结论

To reassemble your device, follow these instructions in reverse order.

14等其他人完成本指南。

作者

与6其他贡献者

Alexander Castanares

于04/01/15注册

870 声望

创作了2篇指南

徽章: 21

+ 18更多徽章

团队

Cal Poly, Team 12-4, Lancaster Spring 2015 Cal Poly, Team 12-4, Lancaster Spring 2015 的会员

CPSU-LANCASTER-S15S12G4

2 名成员

创作了18篇指南

11条评论

Donde encuentro las bocinas no sirven la que tiene

feliper233 - 回复

Donde puedo conseguir las bocinas?

feliper233 - 回复

Where can I get gthe replacement speaker?

rohit jayendra - 回复

where can i get replaicment speaker?

tamaerocksxd - 回复

Where do I get the replacement speakers

Robert - 回复

添加评论

浏览统计数据:

过去 24 小时： 4

过去 7 天： 28

过去 30 天： 137

总计 81,628