跳转到主内容

HTC Flyer MicroUSB Port Replacement

你所需要的

  1. HTC Flyer MicroUSB Port Replacement, Back Cover: 步骤 1 中的图像 1,3 HTC Flyer MicroUSB Port Replacement, Back Cover: 步骤 1 中的图像 2,3 HTC Flyer MicroUSB Port Replacement, Back Cover: 步骤 1 中的图像 3,3
    • Apply pressure along the bottom of the white panel containing the camera and push upwards.

    • It may take some effort, but it will smoothly slide off.

  2. HTC Flyer MicroUSB Port Replacement: 步骤 2 中的图像 1,3 HTC Flyer MicroUSB Port Replacement: 步骤 2 中的图像 2,3 HTC Flyer MicroUSB Port Replacement: 步骤 2 中的图像 3,3
    • Unscrew the four of 3.5mm Torx T5 screws that run along the sides of the exposed innards.

    • All screws in the device will use the Torx T5 screwdriver, so keep it handy.

  3. HTC Flyer MicroUSB Port Replacement: 步骤 3 中的图像 1,3 HTC Flyer MicroUSB Port Replacement: 步骤 3 中的图像 2,3 HTC Flyer MicroUSB Port Replacement: 步骤 3 中的图像 3,3
    • Remove the black protective piece of plastic by sliding it upwards.

    • Remove the two 3.5mm Torx #5 screws holding the protective plastic down on along the sides.

    • A center 3.5mm Torx screw will be covered by "VOID" sticker.

    • Either remove the sticker or jam the screwdriver into the screw, and remove the screw.

    • Remove the protective panel by sliding it upwards.

  4. HTC Flyer MicroUSB Port Replacement: 步骤 4 中的图像 1,2 HTC Flyer MicroUSB Port Replacement: 步骤 4 中的图像 2,2
    • Before removing the back cover, apply some scotch tape to the volume buttons to prevent them from falling out of the back panel.

    • Use a plastic opening tool to lever up the top half of the cover.

    • Lift the back panel up and remove it from the device.

  5. HTC Flyer MicroUSB Port Replacement, Battery: 步骤 5 中的图像 1,2 HTC Flyer MicroUSB Port Replacement, Battery: 步骤 5 中的图像 2,2
    • Gently unfold the black tape along the top that covers the cable attachment points.

    • Leave the tape partially attached so that it can be easily re-attached.

  6. HTC Flyer MicroUSB Port Replacement: 步骤 6 中的图像 1,3 HTC Flyer MicroUSB Port Replacement: 步骤 6 中的图像 2,3 HTC Flyer MicroUSB Port Replacement: 步骤 6 中的图像 3,3
    • Use the tip of a spudger as a lever to disconnect the four cable connectors.

    • Gently pull out these cables after releasing the back piece.

  7. HTC Flyer MicroUSB Port Replacement: 步骤 7 中的图像 1,1
    • Remove the single 2.5mm Torx T5 screw holding the battery down along the top side.

  8. HTC Flyer MicroUSB Port Replacement: 步骤 8 中的图像 1,3 HTC Flyer MicroUSB Port Replacement: 步骤 8 中的图像 2,3 HTC Flyer MicroUSB Port Replacement: 步骤 8 中的图像 3,3
    • Wedge the flat end of a spudger inbetween the battery and the front panel assembly.

    • Run the flat end of a spudger along the top edge of the battery to separate it from the adhesive securing it to the front panel assembly.

    • If you encounter any resistance from the remaining adhesive, simply use the flat end of a spudger to remove the excess adhesive.

  9. HTC Flyer MicroUSB Port Replacement, MicroUSB Port: 步骤 9 中的图像 1,1
    • Use a spudger to unclip the the wires attached to the power jack

    • The clips have a white or black relief tab that, when pressed, releases the wires.

  10. HTC Flyer MicroUSB Port Replacement: 步骤 10 中的图像 1,2 HTC Flyer MicroUSB Port Replacement: 步骤 10 中的图像 2,2
    • Remove the two 2.5mm Torx T5 screws from both sides of the power jack panel.

  11. HTC Flyer MicroUSB Port Replacement: 步骤 11 中的图像 1,2 HTC Flyer MicroUSB Port Replacement: 步骤 11 中的图像 2,2
    • Gently remove the power jack panel.

结论

To reassemble your device, follow these instructions in reverse order.

4等其他人完成本指南。

Joshua

于10/07/14注册

185 声望

撰写一个指南

团队

USF Tampa, Team 8-5, Leahy Fall 2014 USF Tampa, Team 8-5, Leahy Fall 2014 的会员

USFT-LEAHY-F14S8G5

3 名成员

创作了12篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时: 0

过去 7 天: 0

过去 30 天: 1

总计 1,165