跳转到主内容

简介

If your laptop screen is cracked or appears dark while the computer is running, replace the screen.

  1. Flip the 4520s upside-down with the front toward you. Push the two latches below the battery inwards at the same time.
    • Flip the 4520s upside-down with the front toward you.

    • Push the two latches below the battery inwards at the same time.

  2. Remove the battery by holding the latches and sliding the battery away from you.
    • Remove the battery by holding the latches and sliding the battery away from you.

  3. Use a Phillips #1 screwdriver to remove three 2mm screws where the battery was located. Use a Phillips #1 screwdriver to remove three 2mm screws where the battery was located.
    • Use a Phillips #1 screwdriver to remove three 2mm screws where the battery was located.

  4. Flip the 4520s over and rotate it so the back is facing you. Use a metal spudger to peel off two rubber caps located on either side of the battery port.
    • Flip the 4520s over and rotate it so the back is facing you.

    • Use a metal spudger to peel off two rubber caps located on either side of the battery port.

  5. Use a Phillips #1 screwdriver to remove the 3mm screws behind the caps.
    • Use a Phillips #1 screwdriver to remove the 3mm screws behind the caps.

  6. PC 笔记本电池

    An easy fix for a big power boost.

    现在开始购物

    PC 笔记本电池

    An easy fix for a big power boost.

    现在开始购物
  7. Rotate the 4520s and then open it with the screen facing you. The switch cover is located above the keyboard.  Push the switch cover away from you until it comes loose from the 4520s. Lift the switch cover away from the 4520s and set it aside.
    • Rotate the 4520s and then open it with the screen facing you.

    • The switch cover is located above the keyboard. Push the switch cover away from you until it comes loose from the 4520s.

    • Lift the switch cover away from the 4520s and set it aside.

  8. Use a metal spudger to remove four rubber caps at the bottom of the screen border. Use a metal spudger to remove four rubber caps at the bottom of the screen border.
    • Use a metal spudger to remove four rubber caps at the bottom of the screen border.

  9. Use a Torx (T9) head screwdriver to remove the four 5mm screws beneath the rubber caps. Use a Torx (T9) head screwdriver to remove the four 5mm screws beneath the rubber caps.
    • Use a Torx (T9) head screwdriver to remove the four 5mm screws beneath the rubber caps.

  10. Pry open the tabs behind the border of the screen using a metal spudger. Set the border of the screen aside. Set the border of the screen aside.
    • Pry open the tabs behind the border of the screen using a metal spudger.

    • Set the border of the screen aside.

  11. Use a Torx (T9) head screwdriver to remove two 5mm screws above the screen, and two more screws below it. The bottom set of screws is installed on the innermost screw holes.
    • Use a Torx (T9) head screwdriver to remove two 5mm screws above the screen, and two more screws below it.

    • The bottom set of screws is installed on the innermost screw holes.

  12. Above the screen is a bronze port with a cable connected to it.  Disconnect the cable using a metal spudger or your finger.
    • Above the screen is a bronze port with a cable connected to it. Disconnect the cable using a metal spudger or your finger.

  13. Gently push the back cover away.
    • Gently push the back cover away.

  14. Use a Phillips (PH1) head screwdriver to remove eight 2mm screws from the screen.  Four of the screws will be on the left side and four will be on the right. Place the screen face down. Place the screen face down.
    • Use a Phillips (PH1) head screwdriver to remove eight 2mm screws from the screen. Four of the screws will be on the left side and four will be on the right.

    • Place the screen face down.

  15. Peel the ribbon cable away from the screen. Peel the ribbon cable away from the screen. Peel the ribbon cable away from the screen.
    • Peel the ribbon cable away from the screen.

  16. To open the clamp for the ribbon cable, use a spudger to  pry up the metal bar securing it to the screen. Disconnect the cable after freeing it from the metal bar
    • To open the clamp for the ribbon cable, use a spudger to pry up the metal bar securing it to the screen.

    • Disconnect the cable after freeing it from the metal bar

结论

To reassemble your device, follow these instructions in reverse order.

2等其他人完成本指南。

Robert Spencer Harrison

于2016年09月21日注册

902 信誉积分

创作了4篇指南

团队

UC Davis, Team 1-3, Oliver Fall 2016 UC Davis, Team 1-3, Oliver Fall 2016 的会员

UCD-OLIVER-F16S1G3

5 名成员

创作了7篇指南

添加评论

浏览统计数据:

过去的24小时: 5

过去的7天: 21

过去的30天: 67

总计 3,286