简介

Installing a tube.

工具

配件

Using the 4mm Allen wrench, partially unscrew the 4 (22mm) hex screws on the front of the axle casing to allow the axle to slide freely.
  • Using the 4mm Allen wrench, partially unscrew the 4 (22mm) hex screws on the front of the axle casing to allow the axle to slide freely.

添加评论

Using the 8mm Allen wrench, loosen the axle screw until 1/2 of the axle screw is visible. Push the axle screw to reveal the axle rod on the other side.
  • Using the 8mm Allen wrench, loosen the axle screw until 1/2 of the axle screw is visible.

  • Push the axle screw to reveal the axle rod on the other side.

添加评论

Using the Allen wrench, finish unscrewing the axle screw and pull it out.
  • Using the Allen wrench, finish unscrewing the axle screw and pull it out.

  • Hold the wheel when pulling out the axle rod so that the bike does not fall.

添加评论

Pull the wheel from the fork.
  • Pull the wheel from the fork.

添加评论

Look at your tire and determine the correct tube size by locating the number (formated ## x #.##) on the wall of the tire.
  • Look at your tire and determine the correct tube size by locating the number (formated ## x #.##) on the wall of the tire.

  • Bike tubes come with one of two standard valve types: presta and schrader. These guides show the installation of a tube with a presta valve.

添加评论

Mac RAM 套件
加速你的Mac。充分利用它的内存。
Mac RAM 套件
从Mac中清理出更多内存。
Unscrew the cap covering the valve. Remove the spacer that holds the valve in place against the rim of the wheel. Open the valve by turning the nut and pressing the valve in to release air pressure from the tube.
  • Unscrew the cap covering the valve.

  • Remove the spacer that holds the valve in place against the rim of the wheel.

  • Open the valve by turning the nut and pressing the valve in to release air pressure from the tube.

添加评论

Slide the tire lever between the tire and the rim. Push down on the tire lever until the edge of the tire is higher than the edge of the rim. Insert a second tire lever adjacent to  the first.
  • Slide the tire lever between the tire and the rim.

  • Push down on the tire lever until the edge of the tire is higher than the edge of the rim.

  • Insert a second tire lever adjacent to the first.

  • Slowly work one tire lever around the rim until the whole tire is loose.

添加评论

Press the valve through the rim of the wheel. Remove the tube from the tire.
  • Press the valve through the rim of the wheel.

  • Remove the tube from the tire.

添加评论

Partially inflate the tube.
  • Partially inflate the tube.

添加评论

Push the valve through the rim. Push the tube into the tire all the way around the rim of the wheel.
  • Push the valve through the rim.

  • Push the tube into the tire all the way around the rim of the wheel.

添加评论

Push the bead of the tire back into place around the rim.
  • Push the bead of the tire back into place around the rim.

  • Make sure not to pinch the tube between the bead of the tire and the rim. Failure to do so may cause a pinch flat.

添加评论

Inflate the tube to the desired air pressure.
  • Inflate the tube to the desired air pressure.

  • A suggested range of air pressure is located on the wall of the tire (formatted ##-##psi).

添加评论

Close the valve and replace the cap. Close the valve and replace the cap.
  • Close the valve and replace the cap.

添加评论

终点

另外一个人完成了本指南。

Sterling Grande

于2012年10月08日注册

126 信誉积分

创作了4篇指南

团队

Cal Poly, Team 9-14, Amido Fall 2012 Cal Poly, Team 9-14, Amido Fall 2012 的会员

CPSU-AMIDO-F12S9G14

4 名成员

创作了6篇指南

添加评论

浏览统计数据:

过去的24小时: 3

过去的7天: 7

过去的30天: 21

总计 1,509