修复你的物品 社区 商店

Fused LED Light Replacement

简介

The LED light bulb consists of many small LEDs connected in series. Whenever a single LED gets fused, the circuit is broken and the Light bulb stops functioning, even though most of the LEDs are still in working condition.

Use this guide to repair a fused bulb by easily replacing a fused LED with a new LED and completing the closed circuit through which the current flows again and lights the bulb.

你所需要的

  1. Fused LED Light Replacement, Fused LED Light: 步骤 1 中的图像 1，2 Fused LED Light Replacement, Fused LED Light: 步骤 1 中的图像 2，2

    • Remove the upper semi-sphere diffuser by twisting or applying some heat with a heat gun or dryer to soften the adhesive.

    编辑

  2. Fused LED Light Replacement: 步骤 2 中的图像 1，3 Fused LED Light Replacement: 步骤 2 中的图像 2，3 Fused LED Light Replacement: 步骤 2 中的图像 3，3

    • Use a battery or a cell with connecting wires and apply them to the exposed solder ends on each LED.

    • The LED which doesn't lights up is detected as the faulty LED.

    编辑

  4. Fused LED Light Replacement: 步骤 3 中的图像 1，1

    • Using a knife or screwdriver, remove the faulty LED.

    • We need to replace it with a similar LED or a resistor.

    • Connecting the terminals directly can result in an increased current and multiple LED failure.

    编辑

  5. Fused LED Light Replacement: 步骤 4 中的图像 1，2 Fused LED Light Replacement: 步骤 4 中的图像 2，2

    • Using the soldering iron solder an LED or a 100Ω (2W or 5W) resistor into the faulty LED space.

    编辑

  6. Fused LED Light Replacement: 步骤 5 中的图像 1，1

    • Connect the bulb to a power source to detect if it's working.

    编辑

  7. Fused LED Light Replacement: 步骤 6 中的图像 1，2 Fused LED Light Replacement: 步骤 6 中的图像 2，2

    • Finally, twist the light-diffusing dome back on the light bulb.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

4等其他人完成本指南。

作者

与2其他贡献者

Abhay choudhary

于05/16/21注册

237 声望

撰写一个指南

徽章: 7

+ 4更多徽章

团队

York University, Team S1-G10, Melo-Thaiss Summer 2021 York University, Team S1-G10, Melo-Thaiss Summer 2021 的会员

YORK-MELO-THAISS-SU21S1G10

1 名成员

创作了3篇指南

1指南评论

I have a large LED bulb with 8 banks of LEDs. The bulb would flicker at times then stay illuminated for a period. After a short time doing this it would completely stop then come back on. It finally stopped working at all. I engineered myself a couple leads from some old multimeter leads I had collecting dusk. I attached those to a fresh 9v battery then checked each bank of LED. All illuminate as quickly as I touch the leads to the first LED in each bank. What’s the issues with this bulb? It’s not due to a bad LED and breaking the continuity. I also prior to testing with the battery went through each bank getting a solid tone so there’s no loss of power from ATo Z. I’m open to suggestions based on your experience tackling this issue. It’s my first rodeo with the LED bulb. Thanks for your help.

Farron - 回复

添加评论

浏览统计数据:

过去 24 小时： 9

过去 7 天： 44

过去 30 天： 145

总计 8,802