简介

根据本指南以更换你的三星盖乐世S6的音量键。

本指南涉及到拆卸后部玻璃面板。拆卸后部玻璃面板会去除将其固定的双面胶。参考 本指南 以重新安装后部玻璃面板。

将回形针或SIM卡针插入和电源按钮同侧的SIM卡槽的孔中。
  • 将回形针或SIM卡针插入和电源按钮同侧的SIM卡槽的孔中。

  • 按压回形针或卡针,使得SIM卡槽弹出

    • 大力按压可能损坏你的SIM卡卡托

添加评论

将SIM卡托从手机中移除
  • 将SIM卡托从手机中移除

添加评论

  • 将你的手机正面朝下放置。

  • 如果手机的玻璃面板已经碎裂,请在拆卸过程中用胶带固定住整个面板。

  • 将iOpener放置在面板上约60秒以融化固定玻璃面板边缘的封胶。

  • 移动iOpener以加热剩余部分的面板,同样需要60秒。

  • 吹风机,热风枪,或者加热工具也许都会用到,但是千万不要过度加热手机——OLED 屏幕和内部电池都会容易热损坏。

are there any option out there that allows you to heat the adhesive outdoors without any power plug?

Brotan Store - 回复

There's a star in the center of our solar system, you could try that.

John Joiner -

the way we do it at Get it fixed cellphone repair calgary is with a heat gun, wich is way easier than this, make sure to wear some gloves and dont worry to use to much heat as long as you point just to the back of the phone, (the back panel is thick enough to protect the logic board from over heat) instead of the usual blue plastic piece i sugest to use the thinnest metal razor knife and a business card so you can insert the business card and move it all around the frame, those blue plastic things are way too thick that will break the glass panel if you apply to much pressure

get it fixed - 回复

After did that with my own heat pad, the white paint got ripped off but luckily glass back cover did not break. So I scratched all white part of the back cover and now its all transparent.

Jae Chung - 回复

I used a purpose built heating device at 100 degree celsius. Lower temperatures didn't work.

ken - 回复

  • 将吸盘紧紧吸在后部玻璃面板的下部。

If the rear screen is cracked/smashed, you will not be able to use a suction cup to remove it. The suction could would not seal because of the cracks. I tried masking tape, 3M shiny HVAC tape, and others, and the suction could would not seal to those surfaces either.

I ended up using the sharp point of the smudger to remove some shards of glass to get underneath the cover to leverage it up and out. Definitely use gloves and safety glasses if you have to do this.

dougpender - 回复

Thank you for your comment. I needed to see this particular instance of what to do when the back cover was cracked. I was going to try to suction it with tape covering it. This saved me some heartache. You're an angel!!

Jessie Brooks -

  • 本步骤还使用了一个塑料撬片,用来将后部面板从中框分离。如果双面胶的粘性仍然很强,用iOpener再加热一次。

  • 使用吸盘在面板中部用力,旋转你的手腕向上拉后部的边缘。

添加评论

  • 当你打开一个够大的缝隙后,在后部玻璃面板和中框之间插入一个塑料撬片。

At this stage I didn’t use a plastic pick as I think they are too thick and will crack a screen that’s not already cracked. I used a stainless steel

I sesame blade which does a much better job of cutting through the adhesive. Just be careful not to insert it in too far. I sometimes put a mark on my blade to ensure it doesn’t go in too far.

Wayne Lyell - 回复

  • 将塑料撬片绕后部玻璃面板的底部左侧滑动。

添加评论

  • 将塑料撬片沿着手机的电源按钮一侧滑动。

添加评论

  • 将塑料撬片沿着手机顶部滑动。

添加评论

  • 将塑料撬片沿着手机的音量按钮的一侧滑动。

添加评论

  • 按住中框,向上拉后部玻璃面板将其与组件分离。

    • 如果由于双面胶粘性太强,用塑料撬片在玻璃下面滑动数次。

添加评论

  • 在后部面板和中框之间插入塑料撬片。

  • 沿着手机的顶部滑动撬片以清除剩余双面胶。

  • 扭动撬片以分离两部分。

添加评论

  • 此时,后部玻璃面板应该完全从手机上分开。双面胶可能仍然会粘附在两侧上。

  • 拉开后部面板,然后完全分离它们。

  • 参考此指南以重新安装后部玻璃面板。

You should note that the adhesive strip may need to be fully removed from the frame in order to proceed with repairs. The adhesive on my phone covered all of the screws exposed in the next step.

Sean Cruz - 回复

  • 卸下13个3.5毫米用来将中框固定在手机上的Phillips #00螺丝。

Make sure you do not mix up these thirteen screws with a hidden 14th screw under the mid-frame chassis, on the left side of the headphone port, on daughter-board. This 14th screw is shorter than the other screws, so make sure you do not replace it with one of the longer screws. It will push up against the front glass and lift it away from the adhesive.

David Whyte - 回复

  • 紧紧地抓住中框组件的边缘。

  • 向下推电池的同时抬起中框组件,以将其与手机的剩余部分分开。

FIRMLY GRASP IT! - Patrick

Armen Orbelyan - 回复

Bei diesem Schritt sicher sein, dass SIM Card Fach entfernt ist!

zikal - 回复

I found the glue still very sticky here, i had to go around with my picks to free it, its very stuck with a UK version, beware!!

databeat1 - 回复

I damaged my screen here a bit, be careful not too slide your pick between the digitizer and the screen.

Anton -

i suggest to apply heat on the corners of the front screen to lose the adhesive a lil bit and push from the bottom back of the phone right where the wireless charger is because of the charging port

get it fixed - 回复

When grabbing from the bottom, you fun the risk of damaging the charging port and headphone jack. I would suggest starting from the top. This is because the two ports at the bottom slide down into the frame. There is also adhesive that will give you a little resistance.

Alex Philip - 回复

Step 18 is not correct, you have to start from the top. You can damage the charge port

Daniel Yaben - 回复

On mine the adhesive actually tore away part of the colored film on the back of the screen glass rather than separating from it. I’m guessing applying heat to the screen corners first would help avoid this (I didn’t). https://imgur.com/a/V7vZQ

Brian Hardie - 回复

  • 抬起中框将其与手机的剩余部分分离。

what do the numbers ZF-N2 AS WELL AS (F13) AT THE END OF THE MODEL NUMBER, THEN THERE IS REV 5-1-C W G 15221............... WHAT ALL HAS TO MATCH WHEN REPLACING THE MID FRAME.

mike gentry - 回复

  • 使用撬棒的尖端翘起音量键触点的连接器。

添加评论

  • 使用撬棒的平端从中框翘起音量键。

添加评论

  • 使用撬棒的尖端,将键帽从中框推出。

添加评论

  • 使用镊子卸下键帽。

添加评论

结论

根据以下介绍的相反顺序重新安装你的设备。重装后部玻璃面板时,参照 更换后部玻璃粘合剂的指南。

7等其他人完成本指南。

特别感谢这些译者︰

100%

Z.Heng正在帮助我们修复这个世界! 想要作出贡献?
开始翻译 ›

Evan Noronha

于2015年02月05日注册

142,020 信誉积分

创作了177篇指南

团队

iFixit iFixit 的会员

Community

111 名成员

创作了6,679篇指南

添加评论

浏览统计数据:

过去的24小时: 4

过去的7天: 13

过去的30天: 84

总计 10,150