简介

The colored metal casing.

  1. Before opening your iPod, ensure that the hold switch is in the locked position.
    • Before opening your iPod, ensure that the hold switch is in the locked position.

    添加评论

  2. Carefully insert an iPod opening tool in the seam between the metal casing and white plastic top.
    • Carefully insert an iPod opening tool in the seam between the metal casing and white plastic top.

    • Lift the top bezel off the iPod. It's glued on using a mild adhesive, so some force may be required.

    添加评论

    • When removing the bottom bezel, be sure not to bend the plastic surrounding the dock connector.

    • Carefully insert an iPod opening tool in the seam between the metal casing and white plastic bezel.

    • Lift the bottom bezel off the iPod. It's glued on using a mild adhesive, so some force may be required.

    I tried using a heat gun to soften the glue, but it ended up melting the white plastic part.

    gordonhamachi - 回复

    • Remove the following two screws:

      • One #00 Phillips screw with a large head near the headphone jack.

      • One #00 Phillips screw with a smaller head near the side of the iPod. This screw strips easily, so be sure to press down firmly on the screwdriver.

    On the iPod I worked on, #000 Phillips was the correct bit. Not #00.

    Eric - 回复

    • Use a metal spudger to carefully pry the headphone jack out of the casing. DO NOT remove the headphone jack from the iPod entirely, as it is connected via a fragile ribbon connector to the click wheel.

    添加评论

  3. 传播 Fixmas 欢乐
    Get $12 off your purchase of $50 or more with code FIXMAS12
    传播 Fixmas 欢乐
    Get $12 off your purchase of $50 or more with code FIXMAS12
    • Slide the headphone jack out until the white plastic housing is no longer held in place by the metal casing.

    添加评论

    • Remove the newly-revealed Phillips #00 screw from beneath the headphone jack. Be careful, this screw is easily stripped.

    I logged this as a success, but I actually wound up stripping the screw on this step (I printed out earlier instructions that didn't have the warning). Reassembled it without said screw and I'm hoping for the best!

    anja - 回复

    The screw on this step also stripped when I was following this tutorial, despite being very careful and taking the time for everything. This really happens _REALLY_ easily!

    I too reassembled the iPod without this particular screw. So far I've noticed no side-effects from this.

    Ultimately I was able to complete the whole guide and repair the Nano succesfully! :-D

    wil - 回复

    i have also stripped this screw in this step. can i change the display without removing this screw? any help is greatly appreciated

    Lori Baldridge - 回复

    I used a Phillips #000. No issues with the screws.

    JPagan - 回复

    • Lift the bottom bezel bracket out of the iPod.

    添加评论

    • Remove the two Phillips #00 screws from the top of the iPod.

    Had to pick out resin with dentist tool to enable Philips driver to engage screw heads.

    Need to be very slow and careful with sharp end of dentist pick.

    afdelaurier - 回复

    Use a Phillips #000.

    JPagan - 回复

    • The highlighted connector attaches the click wheel and headphone jack to the logic board. This cable must be disconnected from the logic board before continuing.

    添加评论

    • Use a spudger to disconnect the headphone jack cable from the logic board. You need to gently pry the connector toward (or up, if you like, the connector is like LEGO® building blocks) the front of the iPod until it comes loose from the logic board.

    • Special hint for the reassembly: Push the connector inside until it is over the corresponding connector of the logic board. Then insert a thin tool over the connector and push it down onto the logic boards connector.

    When reassembling, the jack connector cable broke :'( iPod woking fine, with a new battery.... but no more sound. Grrrr

    TheRV - 回复

    • Use a spudger to push the logic board through the iPod out of the casing. The click wheel and headphone jack should remain in the iPod.

    • Be careful not to catch the headphone jack and click wheel on the logic board as you remove the logic board and display.

    The headphone ribbon and the click wheel is on the top side of the cover, so be sure to apply force toward the down side to avoid scratching the click wheel's PCB.

    lioneltailhardat - 回复

    Before pushing I carefully used the spudger to move the top bezel (with the hold switch) out of the case first. Be careful, it’s got a tiny ribbon cable. But getting that out first made the logic board slide out relatively easily.

    jack.jansen - 回复

    • When removing the logic board, place the tip of the spudger into the hole where you removed the screw and gently push it out. The crevice will keep it in place and decrease the chance of you damaging your board.

    添加评论

    • Completely remove the display and logic board from the metal casing.

    • When reassembling, ensure that the battery is well seated. If the fit is too tight, the edge of the display will score the inside of the screen window.

    When sliding back the logic board, watch out not to put too much stress on the side with the screen and the window, cause it may lead to annoying stripes on your window

    Jasper Jonkman - 回复

    reassembly : use a small dry paint brush to remove dust and crime from display screen to avoid spots .

    afdelaurier - 回复

结论

To reassemble your device, follow these instructions in reverse order.

29等其他人完成本指南。

iRobot

于2009年09月24日注册

1 信誉积分

创作了623篇指南

添加评论

浏览统计数据:

过去的24小时: 2

过去的7天: 11

过去的30天: 43

总计 51,998