跳转到主内容

简介

This guide requires three prerequisite guides for the proper replacement of the digitizer screen on the front of the Zeki tablet. Please, take a moment to familiarize yourself with those guides. They can be found in the details section of this guide.

  1. Zeki TBQG884B Digitizer Touch Screen, Rear Case: 步骤 1 中的图像 1,2 Zeki TBQG884B Digitizer Touch Screen, Rear Case: 步骤 1 中的图像 2,2
    • Remove the two screws from the end of the device where the ports are located using a Phillips #1 screwdriver.

  2. Zeki TBQG884B Digitizer Touch Screen: 步骤 2 中的图像 1,1
    • Place the tablet down so that the screen is facing away from you.

    • Insert the tip of your opening tool into the small gap between the gray and white plastic covering. Pry it open and you should hear the clips opening up.

    • Gently work your way around the perimeter of the tablet's edge.

  3. Zeki TBQG884B Digitizer Touch Screen: 步骤 3 中的图像 1,2 Zeki TBQG884B Digitizer Touch Screen: 步骤 3 中的图像 2,2
    • Remove the back cover

    • Remove any tape on the speaker and detach the speaker from the back plate.

    • The speaker is connected to the motherboard by two soldered wires. Don't break them when you remove the speaker.

  4. Zeki TBQG884B Digitizer Touch Screen, Motherboard: 步骤 4 中的图像 1,1
    • Disconnect the Wi-Fi antenna cable from the motherboard.

  5. Zeki TBQG884B Digitizer Touch Screen: 步骤 5 中的图像 1,1
    • Using the Phillips #1 screwdriver, remove the three screws from the motherboard..

  6. Zeki TBQG884B Digitizer Touch Screen: 步骤 6 中的图像 1,1
    • Open the ZIF connector. Then, remove the ribbon that connects the motherboard and the screen.

  7. Zeki TBQG884B Digitizer Touch Screen: 步骤 7 中的图像 1,1
    • Disconnect the other ZIF connector on the opposite side of the motherboard.

  8. Zeki TBQG884B Digitizer Touch Screen: 步骤 8 中的图像 1,1
    • Remove the motherboard and now reinsert all connectors into a new motherboard.

    • In order to disconnect the battery and speaker wires from the motherboard, soldering is required. Be cautious as the soldering iron is hot.

  9. Zeki TBQG884B Digitizer Touch Screen, LCD Screen: 步骤 9 中的图像 1,1
    • Use an opening tool to detach the clip between the front frame, and the metal loader.

    • There are several clips on each side of the frame. Detach ALL of them before you open the loader.

  10. Zeki TBQG884B Digitizer Touch Screen: 步骤 10 中的图像 1,1
    • Lift the metal loader up and separate it from the LCD screen.

    • Detach each piece slowly to avoid damaging or dropping any fragile parts.

  11. Zeki TBQG884B Digitizer Touch Screen, Digitizer Touch Screen: 步骤 11 中的图像 1,1
    • Separate the display from the digitizer.

结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

David Wyman

于2015年09月16日注册

343 声望

创作了3篇指南

团队

IUPUI, Team 1-3, Harley Fall 2015 IUPUI, Team 1-3, Harley Fall 2015 的会员

IUPUI-HARLEY-F15S1G3

5 名成员

创作了5篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时: 0

过去 7 天: 2

过去 30 天: 10

总计 750