修复你的物品 社区 商店

YCCTEAM YCC-SW4001 Rumble Motor Replacement

简介

If the YCCTEAM YCC-SW4001's vibration feature is not working as expected, then follow this guide to replace the rumble motors.

The rumble motors are a feature of a controller that vibrates after a certain condition in a game. This condition is different in each game. The intensity of the rumble is fixed, which means it doesn't get more intense or less intense over time. This may be unwanted for some users, so unplugging them could benefit the overall experience.

你所需要的

  1. YCCTEAM YCC-SW4001 Rumble Motor Replacement, Front Case: 步骤 1 中的图像 1，1

    • Use a Phillips #1 screwdriver to remove the eight 9.15 mm screws that secure the back case.

    翻译

  2. YCCTEAM YCC-SW4001 Rumble Motor Replacement: 步骤 2 中的图像 1，3 YCCTEAM YCC-SW4001 Rumble Motor Replacement: 步骤 2 中的图像 2，3 YCCTEAM YCC-SW4001 Rumble Motor Replacement: 步骤 2 中的图像 3，3

    • Use an opening pick to pry the back cover off of the controller.

    • This exposes the battery’s housing.

    翻译

  3. YCCTEAM YCC-SW4001 Rumble Motor Replacement: 步骤 3 中的图像 1，1

    • Use a Phillips #1 screwdriver to remove the three 9.15 mm screws from the back of the controller.

    翻译

  5. YCCTEAM YCC-SW4001 Rumble Motor Replacement: 步骤 4 中的图像 1，3 YCCTEAM YCC-SW4001 Rumble Motor Replacement: 步骤 4 中的图像 2，3 YCCTEAM YCC-SW4001 Rumble Motor Replacement: 步骤 4 中的图像 3，3

    • Delicately lift the front case slightly by pulling it away from the back case.

    • Do not remove the front cover completely; it is still attached to the motherboard by a white ribbon cable.

    翻译

  6. YCCTEAM YCC-SW4001 Rumble Motor Replacement: 步骤 5 中的图像 1，3 YCCTEAM YCC-SW4001 Rumble Motor Replacement: 步骤 5 中的图像 2，3 YCCTEAM YCC-SW4001 Rumble Motor Replacement: 步骤 5 中的图像 3，3

    • Use the tip of the opening pick to flip up the black locking flap of the ZIF connector.

    • The black flap holds the white ribbon cable in place.

    翻译

  7. YCCTEAM YCC-SW4001 Rumble Motor Replacement: 步骤 6 中的图像 1，2 YCCTEAM YCC-SW4001 Rumble Motor Replacement: 步骤 6 中的图像 2，2

    • Use tweezers to disconnect the white ribbon cable from the ZIF connector.

    翻译

  8. YCCTEAM YCC-SW4001 Rumble Motor Replacement: 步骤 7 中的图像 1，1

    • Remove the front case.

    翻译

  9. YCCTEAM YCC-SW4001 Rumble Motor Replacement, Rumble Motor: 步骤 8 中的图像 1，3 YCCTEAM YCC-SW4001 Rumble Motor Replacement, Rumble Motor: 步骤 8 中的图像 2，3 YCCTEAM YCC-SW4001 Rumble Motor Replacement, Rumble Motor: 步骤 8 中的图像 3，3

    • On the front side, unplug the cables connecting the two rumble motors to the circuit board by gripping each cable and pulling away from the corresponding plug with moderate force.

    • When replacing the rumble motors, press each plug down into its socket until it snaps into place.

    翻译

  10. YCCTEAM YCC-SW4001 Rumble Motor Replacement: 步骤 9 中的图像 1，3 YCCTEAM YCC-SW4001 Rumble Motor Replacement: 步骤 9 中的图像 2，3 YCCTEAM YCC-SW4001 Rumble Motor Replacement: 步骤 9 中的图像 3，3

    • Remove the rumble motors from the controller grips.

    翻译
结论

To reassemble your device, follow these instructions in reverse order.

0条评论

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 1

过去 30 天： 3

总计 44