跳转到主内容

修复你的物品

维修的权力

商店

简介

This guide will demonstrate how to replace the LCD and digitizer on the Samsung Galaxy Mega 6.3 smartphone.

  1. Use the opening tool or a fingernail to pry open the rear cover at the top left corner. Once the rear cover is removed, you'll have access to the SIM card, the SD card, and screws.
    • Use the opening tool or a fingernail to pry open the rear cover at the top left corner.

    • Once the rear cover is removed, you'll have access to the SIM card, the SD card, and screws.

  2. After removing the back cover, remove the battery, the SIM card, and SD card (if present). Remove the highlighted PH000 screws from the rear of the phone. Ensure the phone has been powered down via the OS (if possible) before removing the battery.
    • After removing the back cover, remove the battery, the SIM card, and SD card (if present).

    • Remove the highlighted PH000 screws from the rear of the phone.

    • Ensure the phone has been powered down via the OS (if possible) before removing the battery.

  3. Using the opening tool, gently pry the speaker upwards and remove it.
    • Using the opening tool, gently pry the speaker upwards and remove it.

    • The speaker is fragile; take caution when removing it to prevent damage.

  4. 跳过升级

    通过使用多合一工具包维修可以节省成本。

    购买 iPhone 维修工具套装

    跳过升级

    通过使用多合一工具包维修可以节省成本。

    购买 iPhone 维修工具套装
  5. Insert the pry tool along the side of the device.  Pry gently until you hear clicks. Repeat along all sides of the phone. You will continue hearing a clicking sound as the frame begins to release. Gently pull the battery clip up (shown in photo 2).   Then, twist the frame slightly clockwise, as there is a little clip around the camera that needs to be released.
    • Insert the pry tool along the side of the device. Pry gently until you hear clicks.

    • Repeat along all sides of the phone. You will continue hearing a clicking sound as the frame begins to release.

    • Gently pull the battery clip up (shown in photo 2). Then, twist the frame slightly clockwise, as there is a little clip around the camera that needs to be released.

  6. Use the opening tool to remove the LCD cable. Once the back frame has been removed, the motherboard and connectors will be exposed.
    • Use the opening tool to remove the LCD cable.

    • Once the back frame has been removed, the motherboard and connectors will be exposed.

    • Remove the front camera by unscrewing the panel.

    • Disconnect the front camera cable.

  7. Use the heat gun to heat around the edges of the screen. Insert three opening picks between the glass and the silver frame of the phone to pry it open. Do not insert a pick at the bottom of the screen. The back button and the menu button break easily.
    • Use the heat gun to heat around the edges of the screen.

    • Insert three opening picks between the glass and the silver frame of the phone to pry it open.

    • Do not insert a pick at the bottom of the screen. The back button and the menu button break easily.

  8. With the opening picks still inside the phone, lift the screen up toward you. Do not pull it off right away, but leave the screen at an angle. Put the screen down along with the opening picks in order to keep it loose. Heat up the bottom to loosen the adhesive from the back and the menu button. Carefully pull the screen  towards you.  Keep an eye on the bottom to make sure that the buttons are separating from the adhesive.
    • With the opening picks still inside the phone, lift the screen up toward you. Do not pull it off right away, but leave the screen at an angle.

    • Put the screen down along with the opening picks in order to keep it loose. Heat up the bottom to loosen the adhesive from the back and the menu button.

    • Carefully pull the screen towards you. Keep an eye on the bottom to make sure that the buttons are separating from the adhesive.

    • Be very careful when removing the button flex cables from the screen. If these cables are broken, you will need to replace the charging port assembly.

  9. Verify that the buttons are completely separated from the adhesive. Separate the screen from the bezel. Separate the screen from the bezel.
    • Verify that the buttons are completely separated from the adhesive.

    • Separate the screen from the bezel.

结论

To reassemble your device, follow these instructions in reverse order.

45等其他人完成本指南。

lillarrypimp1993

于2015年02月26日注册

849 信誉积分

撰写一个指南

replaced screen everything works fine excepe want pickup network .this was a unlocked phone is there any way replacing it would lock it up again

KENNETH P - 回复

Unless you replaced the board, I can't see how. You might have left something disconnected.

Rongwey - 回复

check your antenna cable connection, it will not pick up a signal if not connected

Ron Lindon - 回复

添加评论

浏览统计数据:

过去的24小时: 2

过去的7天: 10

过去的30天: 31

总计 18,038