跳转到主内容

简介

If your Galaxy A5 won't hold a charge you can use this guide to replace the worn-out battery.

If your battery is swollen, take appropriate precautions.

This guide involves removing the display and the mid frame. You may need new adhesive to attach the battery and the display to the phone.

Before disassembling your phone, discharge the battery below 25%. The battery can catch fire and/or explode if accidentally punctured, but the chances of that happening are much lower if discharged.

  1. Switch off your phone. If your screen is cracked you want to cover the front panel with tape to protect yourself from glass shards and get a better grip to lift it. Use an iOpener to soften the glue on the edge of the display. Concentrate on the sides first and then on the bottom part.
    • Switch off your phone.

    • If your screen is cracked you want to cover the front panel with tape to protect yourself from glass shards and get a better grip to lift it.

    • Use an iOpener to soften the glue on the edge of the display. Concentrate on the sides first and then on the bottom part.

    • With an iSclack or a suction handle you can lift the display a little bit to get in the gap with an opening pick.

    • The phone screen is composed of two layers (glass and display). Ensure that you are removing both layers and not splitting the two layers.

    • In the beginning just insert the tip of the opening pick and slide along the side to loosen the glue. Leave the top and bottom alone for now.

  2. When the glue is loosened enough on the side you can lift the display a little bit more to get underneath the display with an opening pick. Take a second opening pick and work your way around the bottom edge. The software buttons in the lower left and right corners of the screen have ribbon cables that are glued to the display. Be very careful that your pick cuts between the screen and buttons and does not cut these wires.
    • When the glue is loosened enough on the side you can lift the display a little bit more to get underneath the display with an opening pick.

    • Take a second opening pick and work your way around the bottom edge.

    • The software buttons in the lower left and right corners of the screen have ribbon cables that are glued to the display. Be very careful that your pick cuts between the screen and buttons and does not cut these wires.

    • Repeat the last step and this one on the other side.

  3. Grab the iOpener once again to heat up the bottom and top part to further soften the glue. Now you will be able to move the picks at the bottom closer to the home button and eventually open the display towards the top. Don't open the display all the way. It is still connected to the motherboard.
    • Grab the iOpener once again to heat up the bottom and top part to further soften the glue.

    • Now you will be able to move the picks at the bottom closer to the home button and eventually open the display towards the top.

    • Don't open the display all the way. It is still connected to the motherboard.

    • The home button may stick to the display assembly or remain on the midframe. Keep an eye on it if your new display does not come with one already attached.

  4. In the top right corner you can find the connector of the display. Use a spudger to unplug it. Now you can remove the display. Now you can remove the display.
    • In the top right corner you can find the connector of the display. Use a spudger to unplug it.

    • Now you can remove the display.

  5. Take the home button out and put it aside. Remove the SD card tray and the SIM card tray. Remove the twelve Phillips #00 screws on the midframe.
    • Take the home button out and put it aside.

    • Remove the SD card tray and the SIM card tray.

    • Remove the twelve Phillips #00 screws on the midframe.

  6. Insert the tip of an opening pick right below the volume buttons to get the midframe out. This should unhinge the clips on the side and the bottom left corner. Put the pick underneath the volume buttons to pop out the top left corner. Put the pick underneath the volume buttons to pop out the top left corner.
    • Insert the tip of an opening pick right below the volume buttons to get the midframe out. This should unhinge the clips on the side and the bottom left corner.

    • Put the pick underneath the volume buttons to pop out the top left corner.

  7. Push the top part towards the opened left side to rotate the midframe out. Push the top part towards the opened left side to rotate the midframe out.
    • Push the top part towards the opened left side to rotate the midframe out.

  8. Use a spudger to disconnect the battery. With an opening pick you can get between the midframe and the battery to separate it from the glue. Pry out the battery.
    • Use a spudger to disconnect the battery.

    • With an opening pick you can get between the midframe and the battery to separate it from the glue.

    • Pry out the battery.

    • The midframe is very fragile. Be careful when prying out the battery.

结论

To reassemble your device, follow these instructions in reverse order. Reapply adhesive where necessary.

43等其他人完成本指南。

Tobias Isakeit

于2014年03月31日注册

56,502 信誉积分

创作了120篇指南

团队

iFixit iFixit 的会员

Community

107 名成员

创作了9,558篇指南

Shattered my screen and cut off the wires for both the “home” and “overview” buttons. There is nothing wrong with this guide but a few simple tips would have saved me a lot of pain (and my favorite phone which is now garbage). First, the screen is made of two layers (glass sandwiched to an LCD) you need to make sure you are prying out both of these layers and not just one. Second, there is no indication of how hot to get the phone for softening the glue (presumably getting it too hot is also detrimental). I guess I didn’t get it hot enough because my screen never budged. I tried sliding in a razor blade just to get things started and the screen immediately shattered. Lastly, the guide is not explicit that the “home” and “overview” buttons are glued to the screen and have wires that pass along the very edge of of the screen. Sliding a pick across the bottom of the phone is likely to cut right through these wires. This is not repairable. Thanks ifixit for taking my money and destroying my phone.

Andrew Hall - 回复

Good evening.

I changed the battery successfully because the old one was stuck on 51% when charging, but the new has the same behaviour!! What kind of problems can this phone have?

Luca

Luca Di Liello - 回复

添加评论

浏览统计数据:

过去的24小时: 70

过去的7天: 440

过去的30天: 2,094

总计 93,861