简介

Removing the reset button will allow you to replace it if it is not functioning properly.

Turn the device so that the bottom is facing up.
  • Turn the device so that the bottom is facing up.

添加评论

Use the plastic opening tool to carefully lift the rubber stops in each corner. Do not completely remove the rubber stops, because they are difficult to replace. Do not completely remove the rubber stops, because they are difficult to replace.
  • Use the plastic opening tool to carefully lift the rubber stops in each corner.

  • Do not completely remove the rubber stops, because they are difficult to replace.

添加评论

Unscrew the 4 11.8 mm T-8 Torx screws from each corner of the device. Unscrew the 4 11.8 mm T-8 Torx screws from each corner of the device.
  • Unscrew the 4 11.8 mm T-8 Torx screws from each corner of the device.

添加评论

Lift the lower case straight up from the rest of the router. Lift the lower case straight up from the rest of the router.
  • Lift the lower case straight up from the rest of the router.

添加评论

Remove the clear plastic casing by lifting it straight up from the router. Remove the clear plastic casing by lifting it straight up from the router.
  • Remove the clear plastic casing by lifting it straight up from the router.

添加评论

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Separate the motherboard from the top shell by lifting it straight up from the router. Separate the motherboard from the top shell by lifting it straight up from the router.
  • Separate the motherboard from the top shell by lifting it straight up from the router.

添加评论

Turn the motherboard, so that the top is facing upwards.
  • Turn the motherboard, so that the top is facing upwards.

  • Place the motherboard on a clean flat surface.

添加评论

Remove the yellow tape that holds the wire. Make sure that you set the tape aside on a clean surface, so that it can be reused.
  • Remove the yellow tape that holds the wire.

  • Make sure that you set the tape aside on a clean surface, so that it can be reused.

添加评论

Use tweezers to gently pull the metal bracket that connects the antenna to the motherboard. The wire should now be completely separate from the motherboard. The wire should now be completely separate from the motherboard.
  • Use tweezers to gently pull the metal bracket that connects the antenna to the motherboard.

  • The wire should now be completely separate from the motherboard.

添加评论

Extend the antenna away from the device, so that it becomes straight.
  • Extend the antenna away from the device, so that it becomes straight.

添加评论

Find the clips that hold the antenna onto the router. Use one hand to push the clips in, while using your other hand to pull out the antenna. You may need to gently twist the antenna so it can separate from the hole. The antenna may take considerable force to remove.
  • Find the clips that hold the antenna onto the router.

  • Use one hand to push the clips in, while using your other hand to pull out the antenna. You may need to gently twist the antenna so it can separate from the hole.

  • The antenna may take considerable force to remove.

添加评论

Completely separate the antenna and wire from the rest of the device.
  • Completely separate the antenna and wire from the rest of the device.

添加评论

Remove the metal frame. Remove the metal frame.
  • Remove the metal frame.

添加评论

Turn over the motherboard.
  • Turn over the motherboard.

添加评论

Do not refer to the pictures in this step for correct soldering and de-soldering techniques. They are solely for illustration purposes.
  • Do not refer to the pictures in this step for correct soldering and de-soldering techniques. They are solely for illustration purposes.

  • Desolder the four connections between the reset button and the motherboard

  • For proper soldering and desoldering techniques, refer here.

  • Pull the reset button from the other side of the mother board once the solder is liquid.

添加评论

结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

Jonathon Sather

于2013年01月23日注册

27 信誉积分

创作了3篇指南

团队

Cal Poly, Team 3-31, Amido Winter 2013 Cal Poly, Team 3-31, Amido Winter 2013 的会员

CPSU-AMIDO-W13S3G31

3 名成员

创作了6篇指南

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 0

过去的30天: 2

总计 580