跳转到主内容

简介

Use this guide to remove or replace the heat sink.

Don't forget to follow our thermal paste application guide after you have removed your heat sink.

    • Remove the following ten screws securing the lower case to the upper case:

    • Two 2.3 mm P5 Pentalobe screws

    • Eight 3.0 mm P5 Pentalobe screws

    • Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from to avoid damaging your device.

  1. MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement: 步骤 2 中的图像 1,1
    • Wedge your fingers between the upper case and the lower case.

    • Gently pull the lower case away from the upper case to remove it.

  2. MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement: 步骤 3 中的图像 1,2 MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement: 步骤 3 中的图像 2,2
    • The lower case is connected to the upper case with two plastic clips near its center.

    • During reassembly, gently push down the center of the lower case to reattach the two plastic clips.

  3. MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement, Battery Connector: 步骤 4 中的图像 1,1
    • If necessary, remove the plastic cover adhered to the battery contact board.

  4. MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement: 步骤 5 中的图像 1,2 MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement: 步骤 5 中的图像 2,2
    • Use the flat end of a spudger to lift the battery connector straight up out of its socket on the logic board.

    • Be sure you lift up only on the connector itself, not the socket, or you risk permanent damage to the logic board.

  5. MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement: 步骤 6 中的图像 1,1
    • Bend the battery connector up out of the way to prevent accidental contact with its socket during your repair.

  6. MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement, Heat Sink: 步骤 7 中的图像 1,3 MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement, Heat Sink: 步骤 7 中的图像 2,3 MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement, Heat Sink: 步骤 7 中的图像 3,3
    • Carefully remove the rubber fan bumper from the edge of the heat sink.

    • The fan bumper wraps around the heat sink and fits into slots in the fan duct. During reassembly, be sure to fit the tabs into the notches in the fan duct.

  7. MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement: 步骤 8 中的图像 1,2 MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement: 步骤 8 中的图像 2,2
    • Use the flat end of a spudger to peel the four foam stickers off of the heat sink screws.

  8. MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement: 步骤 9 中的图像 1,1
    • Remove the following screws securing the heat sink to the logic board:

    • Four 2.6 mm T5 screws

    • One 2.4 mm Phillips #000 screw

  9. MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement: 步骤 10 中的图像 1,2 MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement: 步骤 10 中的图像 2,2
结论

To reassemble your device, follow these instructions in reverse order.

13等其他人完成本指南。

Sam Goldheart

于2012年10月18日注册

453,860 声望

创作了548篇指南

团队

iFixit iFixit 的会员

Community

146 名成员

创作了16,118篇指南

一条评论

Do I need Anti-Static Wrist Strap ?

if so, where do i connect it, to laptop ?

mikele - 回复

添加评论

浏览统计数据:

过去 24 小时: 7

过去 7 天: 39

过去 30 天: 176

总计 18,780