简介

Use this guide to replace your audio cable.

Unplug your MacBook Air and power it off before you proceed.
  • Unplug your MacBook Air and power it off before you proceed.

  • Remove ten Phillips screws securing the lower case to the MacBook Air:

    • Six 2.8 mm screws

    • Two 3.8 mm screws

    • Two 5.4 mm screws

添加评论

Slightly lift the lower case near the vents and push it toward the rear of the computer to free the mounting tabs.
  • Slightly lift the lower case near the vents and push it toward the rear of the computer to free the mounting tabs.

添加评论

  • Disconnect the battery connector by pulling it straight out of its socket.

添加评论

  • Remove the following nine screws securing the battery to the Air:

    • Four 2.9 mm Phillips.

    • Four 3.8 mm Phillips.

    • One 7.2 mm Phillips.

添加评论

  • Lift the battery out of the Air.

添加评论

  • Remove the following two screws securing the speaker assembly to the upper case.

    • One 3 mm Phillips.

    • One 5.8 mm Phillips.

添加评论

  • Use a spudger to lift the audio-out connector board off the adhesive that secures it to the hard drive bracket.

  • Disconnect the audio out connector from its socket.

添加评论

  • Rotate the speaker assembly toward the center of the Air.

  • Use a spudger to pry the speaker cable connector up off the audio board.

添加评论

  • Disconnect the port hatch ribbon cable from the logic board by pulling it straight up by its black pull tab.

  • If necessary, pull the audio out ribbon cable off the adhesive securing it to the upper case.

添加评论

  • Use the pointed end of a spudger to de-route the microphone cable from the hard drive bracket.

添加评论

  • Remove the following screws securing the hard drive to the upper case:

    • Two 3.9 mm Phillips screws.

    • One 4.7 mm Phillips screw.

      • This may be a Torx T6 screw.

添加评论

  • Use the tip of a spudger to remove the cosmetic screw cover to reveal the last remaining screw securing the hard drive.

添加评论

  • Remove the 4.7 mm Phillips screw securing the hard drive to the upper case.

添加评论

  • Lift the hard drive slightly and use a spudger to pry the audio cable connector up off the logic board.

  • Peel the audio cable off the adhesive securing it to the upper case.

Hello. When i tried to pry the audio cable connector up off the logic board, the chip was disconnected from the logic board. How can i stick it back ?

Theo chry - 回复

结论

To reassemble your device, follow these instructions in reverse order.

94等其他人完成本指南。

Great! it works!

Jorge - 回复

It's perfect guide. I had a same situaton with my Air and cable that I ordered from here works perfect.

Thanks

William Sawyer - 回复

I had no audio, with the sound icon in menu bar absent and volume panel grayed out. This repair worked! Be sure to label each screw type from each step of the guide (some screws that were supposed to be same mm from two different steps were not). Be careful not to strip screws when removing them, and not to cross-thread when reinserting. Thanks for the guide.

angbra - 回复

It works , easy to follow guide and super fast shipping of the cable (just 6days), thanks guys ! BRGDS from Spain

hectorramirezrodriguez - 回复

I have sound!!! Cable that i ordered here works perfekt for me too. Thank you very much.

michal - 回复

Can i use it with a MacBook Air mid 2011?

Leandro Oriente - 回复

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 8

过去的30天: 48

总计 53,643