跳转到主内容

修复你的物品

维修的权力

商店

简介

Use this guide to replace the audio board in a 2019 MacBook Air. This board houses the headphone jack.

  1. Before starting this procedure, you must disable your Mac's Auto Boot feature. Auto Boot powers on your Mac when you open the lid, and may be accidentally triggered during disassembly. Use this guide or follow the abbreviated instructions below to disable Auto Boot.
    • Before starting this procedure, you must disable your Mac's Auto Boot feature. Auto Boot powers on your Mac when you open the lid, and may be accidentally triggered during disassembly. Use this guide or follow the abbreviated instructions below to disable Auto Boot.

    • Completely power off and unplug your MacBook Air before you start. Close the display and flip the entire laptop upside-down.

    • Use a P5 driver to remove the following screws:

    • Two 7.9 mm screws

    • Two 7.1 mm screws

    • Six 2.6 mm screws

  2. Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.
    • Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.

    • Remove the lower case.

  3. Peel back the tape covering the battery connector enough to reveal the connector underneath.
    • Peel back the tape covering the battery connector enough to reveal the connector underneath.

  4. Use a spudger to slide the battery connector parallel to the logic board and out of its socket on the logic board. Use a spudger to slide the battery connector parallel to the logic board and out of its socket on the logic board.
    • Use a spudger to slide the battery connector parallel to the logic board and out of its socket on the logic board.

  5. 跳过升级

    通过使用多合一工具包维修可以节省成本。

    购买 iPhone 维修工具套装

    跳过升级

    通过使用多合一工具包维修可以节省成本。

    购买 iPhone 维修工具套装
  6. Slide the tip of a spudger underneath the speaker cable and pry straight up to disconnect the speaker. Slide the tip of a spudger underneath the speaker cable and pry straight up to disconnect the speaker.
    • Slide the tip of a spudger underneath the speaker cable and pry straight up to disconnect the speaker.

  7. Use a T4 Torx driver to remove the three 1.4 mm screws securing the audio board cable bracket. Remove the cable bracket.
    • Use a T4 Torx driver to remove the three 1.4 mm screws securing the audio board cable bracket.

    • Remove the cable bracket.

  8. Use the flat end of a spudger to pry the audio board connector straight up and disconnect it. Use the flat end of a spudger to pry the audio board connector straight up and disconnect it.
    • Use the flat end of a spudger to pry the audio board connector straight up and disconnect it.

  9. Use the flat end of a spudger to pry the Touch ID sensor connector straight up and disconnect it. Use the flat end of a spudger to pry the Touch ID sensor connector straight up and disconnect it.
    • Use the flat end of a spudger to pry the Touch ID sensor connector straight up and disconnect it.

  10. Remove the following screws:
    • Remove the following screws:

    • Two 4.3 mm, T5 Torx screws

    • One 2.4 mm, T4 Torx screw

  11. Slide the flat end of a spudger underneath the Touch ID sensor cable to slice through the adhesive securing it to the audio board.
    • Slide the flat end of a spudger underneath the Touch ID sensor cable to slice through the adhesive securing it to the audio board.

  12. Remove the audio board.
    • Remove the audio board.

结论

Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before installing.

To reassemble your device, follow the above steps in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Check out our Answers community for troubleshooting help.

Adam O'Camb

于2015年04月11日注册

105,305 信誉积分

创作了322篇指南

团队

iFixit iFixit 的会员

Community

128 名成员

创作了13,049篇指南

添加评论

浏览统计数据:

过去的24小时: 2

过去的7天: 9

过去的30天: 49

总计 124