修复你的物品 社区 商店

Logitech Harmony Smart Control Hub Light Bulb Replacement

简介

Learn how to disassemble the Logitech Harmony Smart Control hub, remove a burned out or defective light bulb or bulb(s), and replace it with new one(s).

This repair requires soldering. View the soldering guide at:

Soldering Guide

你所需要的

  1. Logitech Harmony Smart Control Hub Light Bulb Replacement, Light Bulb: 步骤 1 中的图像 1，2 Logitech Harmony Smart Control Hub Light Bulb Replacement, Light Bulb: 步骤 1 中的图像 2，2

    • Use a spudger to lift up one of the rubber pads on the bottom of the hub.

    • Pull back the rubber pad and remove it. This will expose the screws on the bottom of the device.

    • Repeat for the second rubber pad.

    编辑

  2. Logitech Harmony Smart Control Hub Light Bulb Replacement: 步骤 2 中的图像 1，2 Logitech Harmony Smart Control Hub Light Bulb Replacement: 步骤 2 中的图像 2，2

    • Use a PH00 screwdriver bit to remove the four 6mm Phillips screws on the bottom of the device.

    编辑

  4. Logitech Harmony Smart Control Hub Light Bulb Replacement: 步骤 3 中的图像 1，2 Logitech Harmony Smart Control Hub Light Bulb Replacement: 步骤 3 中的图像 2，2

    • Use a spudger to separate the top and bottom pieces of the device.

    编辑

  5. Logitech Harmony Smart Control Hub Light Bulb Replacement: 步骤 4 中的图像 1，2 Logitech Harmony Smart Control Hub Light Bulb Replacement: 步骤 4 中的图像 2，2

    • Use the PH00 screwdriver bit to unscrew the three 4mm Phillips screws on the control board.

    编辑

  6. Logitech Harmony Smart Control Hub Light Bulb Replacement: 步骤 5 中的图像 1，2 Logitech Harmony Smart Control Hub Light Bulb Replacement: 步骤 5 中的图像 2，2

    • Place the end of the opening tool under the yellow corner of the circuit board as shown.

    • Gently push upward to pry the board from its housing.

    编辑

  7. Logitech Harmony Smart Control Hub Light Bulb Replacement: 步骤 6 中的图像 1，3 Logitech Harmony Smart Control Hub Light Bulb Replacement: 步骤 6 中的图像 2，3 Logitech Harmony Smart Control Hub Light Bulb Replacement: 步骤 6 中的图像 3，3

    • Determine which of the five bulbs are defective.

    • Turn the board over to expose the bulb solder.

    • Using a soldering iron, remove the solder and bulb. Replace with a new bulb and re-solder.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

2等其他人完成本指南。

作者

与7其他贡献者

Josh Hendricks

于09/17/15注册

464 声望

创作了4篇指南

徽章: 7

+ 4更多徽章

团队

IUPUI, Team 3-2, Harley Fall 2015 IUPUI, Team 3-2, Harley Fall 2015 的会员

IUPUI-HARLEY-F15S3G2

4 名成员

创作了5篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时： 1

过去 7 天： 1

过去 30 天： 1

总计 532