How to Replace the Adhesive for Your Motorola Phone

简介

Follow this guide to replace the camera bezel and back cover adhesive pads in your Motorola phone. This process is a general procedure that applies to any Motorola phone with a plastic back cover and separate camera bezel.

If your back cover comes off in one piece, follow this guide.

你所需要的

步骤 1 Remove the old adhesive

How to Replace the Adhesive for Your Motorola Phone, Remove the old adhesive: 步骤 1 中的图像 1，1

Use the flat end of a spudger or your fingers to scrape and remove the old adhesive from the phone body.
Pay attention to areas around the cameras and outer edge of the phone. Any remaining chunks will prevent your part from aligning properly.

编辑

步骤 2 Remove the adhesive backing

How to Replace the Adhesive for Your Motorola Phone, Remove the adhesive backing: 步骤 2 中的图像 1，1

Peel and remove the white adhesive backing from the camera bezel's new adhesive pad.

编辑

步骤 3 Align the adhesive pad

How to Replace the Adhesive for Your Motorola Phone, Align the adhesive pad: 步骤 3 中的图像 1，1

In this step, you'll use the camera module bumps to help align the adhesive to the camera bezel.
Lay the adhesive pad over the cameras, with the sticky side facing upward.

编辑

步骤 4 Apply the adhesive

How to Replace the Adhesive for Your Motorola Phone, Apply the adhesive: 步骤 4 中的图像 1，3

How to Replace the Adhesive for Your Motorola Phone, Apply the adhesive: 步骤 4 中的图像 2，3

How to Replace the Adhesive for Your Motorola Phone, Apply the adhesive: 步骤 4 中的图像 3，3

Lay the camera bezel over the cameras and press it onto the adhesive pad.
Lift the camera bezel and adhesive pad from the phone.

编辑

步骤 5 Remove the protective film

How to Replace the Adhesive for Your Motorola Phone, Remove the protective film: 步骤 5 中的图像 1，1

Peel and remove the blue protective film from the camera bezel.

编辑

步骤 6 Install the camera bezel

How to Replace the Adhesive for Your Motorola Phone, Install the camera bezel: 步骤 6 中的图像 1，1

Place the bezel over the cameras.
Press firmly to adhere the bezel to the phone body.

编辑

步骤 7 Clean the back cover

How to Replace the Adhesive for Your Motorola Phone, Clean the back cover: 步骤 7 中的图像 1，1

Use the flat end of a spudger or your fingers to remove the old adhesive from the back cover.
Any remaining adhesive will prevent the cover from seating properly.
If you're having trouble removing the adhesive, apply a heated iOpener to soften the adhesive.
Applying isopropyl alcohol turns the adhesive into a messy residue and is not recommended for this step.

编辑

步骤 8 Remove the adhesive backing

How to Replace the Adhesive for Your Motorola Phone, Remove the adhesive backing: 步骤 8 中的图像 1，1

Peel and remove the white adhesive backing from the back cover's new adhesive pad.

编辑

步骤 9 Apply the adhesive

How to Replace the Adhesive for Your Motorola Phone, Apply the adhesive: 步骤 9 中的图像 1，2

How to Replace the Adhesive for Your Motorola Phone, Apply the adhesive: 步骤 9 中的图像 2，2

Line up the new adhesive on the phone and lay it onto the frame.
Be very careful aligning the adhesive. It's very sticky, and only properly adheres the first time.
Press down firmly on the adhesive along the perimeter of the midframe to secure it.

编辑

步骤 10 Remove the protective film

How to Replace the Adhesive for Your Motorola Phone, Remove the protective film: 步骤 10 中的图像 1，1

Grab and peel the blue protective film, beginning with the cutout.
Remove the protective film.
Be sure that the adhesive pad doesn't stick to the film as you pull.

编辑

步骤 11 Install the back cover

How to Replace the Adhesive for Your Motorola Phone, Install the back cover: 步骤 11 中的图像 1，2

How to Replace the Adhesive for Your Motorola Phone, Install the back cover: 步骤 11 中的图像 2，2

Align the back cover over the phone.
Press down firmly along the perimeter of the cover and around the camera bezel to secure it with the new adhesive.

编辑