Framework Laptop 16" Midframe Replacement

简介

Use this guide to replace the midframe in your Framework 16" laptop.

Note: the laptop used in this guide is a generic setup of one US keyboard, one numpad module, and two touchpad spacers. Your setup might vary, but the procedure should remain the same.

你所需要的

步骤 1 Before you begin

Framework Laptop 16" Midframe Replacement, Before you begin: 步骤 1 中的图像 1，2

Framework Laptop 16" Midframe Replacement, Before you begin: 步骤 1 中的图像 2，2

Unplug all cables and fully shut down your laptop.
If your repair requires a spudger, a T5 Torx, or a Phillips screwdriver, you can use the included Framework screwdriver. Whichever works best for you!

编辑

步骤 2 Unlock the Input Modules

Framework Laptop 16" Midframe Replacement, Unlock the Input Modules: 步骤 2 中的图像 1，3

Framework Laptop 16" Midframe Replacement, Unlock the Input Modules: 步骤 2 中的图像 2，3

Framework Laptop 16" Midframe Replacement, Unlock the Input Modules: 步骤 2 中的图像 3，3

Use your fingernail to pull out the two Input Module latches and unlock them.
The latch will show red if it's unlocked.

编辑

步骤 3 Remove the touchpad spacers

Framework Laptop 16" Midframe Replacement, Remove the touchpad spacers: 步骤 3 中的图像 1，3

Framework Laptop 16" Midframe Replacement, Remove the touchpad spacers: 步骤 3 中的图像 2，3

Framework Laptop 16" Midframe Replacement, Remove the touchpad spacers: 步骤 3 中的图像 3，3

Use your fingers to slide the touchpad spacer toward the bottom edge of the laptop and unclip it.
If you're having trouble, check if the corresponding Input Module latch is properly unlocked.
Lift the touchpad spacer off the laptop and remove it.

编辑

步骤 4

Repeat the same procedure for the other touchpad spacer.

编辑

步骤 5 Remove the touchpad

Framework Laptop 16" Midframe Replacement, Remove the touchpad: 步骤 5 中的图像 1，3

Framework Laptop 16" Midframe Replacement, Remove the touchpad: 步骤 5 中的图像 2，3

Framework Laptop 16" Midframe Replacement, Remove the touchpad: 步骤 5 中的图像 3，3

Use your fingers to slide the touchpad toward the bottom edge of the laptop and disconnect it.
If you're having trouble, check if the Input Module latches are properly unlocked.
Lift the touchpad and remove it.
During reassembly, perform the following:
Place the touchpad flat on its cutout so its clips are properly aligned.
Press the touchpad down and slide it into place so it lines up evenly with the bottom edge of the laptop.

编辑

步骤 6 Remove the keyboard

Framework Laptop 16" Midframe Replacement, Remove the keyboard: 步骤 6 中的图像 1，3

Framework Laptop 16" Midframe Replacement, Remove the keyboard: 步骤 6 中的图像 2，3

Framework Laptop 16" Midframe Replacement, Remove the keyboard: 步骤 6 中的图像 3，3

The keyboard is held in place with strong magnets. Apply gradually increasing force to avoid having the keyboard violently eject.
Grip the two pull tabs along the bottom of the keyboard.
Lift the pull tabs until the keyboard magnets release.
Remove the keyboard.
During reassembly, make sure the keyboard is seated properly on its alignment pegs and sits evenly with the edges of the laptop.

编辑

步骤 7 Remove the numpad

Framework Laptop 16" Midframe Replacement, Remove the numpad: 步骤 7 中的图像 1，3

Framework Laptop 16" Midframe Replacement, Remove the numpad: 步骤 7 中的图像 2，3

Framework Laptop 16" Midframe Replacement, Remove the numpad: 步骤 7 中的图像 3，3

The numpad is held in place with strong magnets. Apply gradually increasing force to avoid having the numpad violently eject.
Grip the pull tab at the bottom of the numpad.
Lift the pull tab until the numpad magnets release.
Remove the numpad.
During reassembly, make sure the numpad is seated properly on its alignment pegs and sits flush with the edges of the laptop.

编辑

步骤 8 Disconnect the midframe cable

Framework Laptop 16" Midframe Replacement, Disconnect the midframe cable: 步骤 8 中的图像 1，2

Framework Laptop 16" Midframe Replacement, Disconnect the midframe cable: 步骤 8 中的图像 2，2

Grip the black pull tab on the midframe cable press connector.
Lift up to disconnect the midframe cable.

编辑

步骤 9 Loosen the midframe screws

Framework Laptop 16" Midframe Replacement, Loosen the midframe screws: 步骤 9 中的图像 1，2

Framework Laptop 16" Midframe Replacement, Loosen the midframe screws: 步骤 9 中的图像 2，2

The midframe screws are ordered from 2–17 (number 1 is the press connector). You don't have to follow the order, but you can use it to help keep track of the screws you've loosened.
Use a T5 Torx screwdriver to loosen the 16 captive screws securing the midframe.
During reassembly, follow the order (starting with 2) to reinstall the screws across the midframe evenly.

编辑

步骤 10 Remove the midframe

Framework Laptop 16" Midframe Replacement, Remove the midframe: 步骤 10 中的图像 1，2

Framework Laptop 16" Midframe Replacement, Remove the midframe: 步骤 10 中的图像 2，2

Use your fingernail to lift the bottom edge of the midframe enough to grip it with your fingers.

编辑

步骤 11

Lift the midframe off the laptop and remove it.
During reassembly, make sure the midframe sits evenly on its alignment pegs before tightening the screws.