简介

本指南将一步一步的指导您如何更换DualShock4 控制器的充电口。

  1. 使用Phillips #00 螺丝刀移除四颗6.0mm固定后面板的螺丝。
    • 使用Phillips #00 螺丝刀移除四颗6.0mm固定后面板的螺丝。

    • 切勿使用强力来松开螺丝,否则会造成螺纹的永久性损坏,从而导致无法拆卸手柄。

    添加评论

  2. 从左肩处开始
    • 左肩处开始

      • 将撬棒插入左肩来撬开一个开口

      • 在开口处滑动来打开更多的空间

      • 取下撬棒,打开手柄壳。

    • 右肩重复这些步骤。

    Shoulders are where L1/L2/R1/R2 are, not the %#*@ handles. Confusing instructions.

    foxhoundunit89 - 回复

    Quick tip: Be VERY careful at this step not to dislodge the tiny spring attached to the L2/R2 buttons. While removing the cover, it's easy to pull off either L2/R2 button. Inadvertently pulling off either button will also remove the tiny spring as well. While not too difficult to reassemble, it's not obvious where the spring goes as the spring is almost completely hidden along the side of the button (on the inside).

    I just successfully completed analog stick replacements for two controllers. I completed the first repair without any trouble but managed to dislodge (and almost lose) the spring on the second time around. Needless to say, I spent some time trying to figure out where the spring is supposed to go (no photos of this anywhere). By sheer luck, I figured it out on my own. :)

    Good luck and take your time--especially the first time!

    Michael Whang - 回复

    couldn't have posted pics for me? :D

    kimsballs -

    Golden tip but I would add a thing or two.

    Most probably both triggers R1&R2 will stay in lower half of the pad case with springs hanging there.

    You must take them of their lower case sockets before assembly and fit them bellow L1&L2

    When you feel click when fitting them and spring works like on normal assembled pad you're done.

    If thats not the case do not try to assemble lower casing half as triggers will not work properly.

    Simon -

    if you lost the springs unfortunately, the triggers would still work but it is harder to get to the precise digital press. In other words you will have hard time to create a light press than a hard press.

    meaningless -

    • 将一个撬棒楔入壳体来打开以下按钮附近的卡扣:

      • Share键

      • Options键

    • 将控制器塑料外壳分开,注意两者依然通过排线连接。

    • 3个小模块经常从框架中跑出,为了避免损失,请保持工作台的干净整洁。

      • 2个触发弹簧

      • 1个灰色复位按钮扩展

    You can't just pull the casing halves apart. There is a plastic bar that is part of the casing and separates the L1 and R1 buttons from the L2 and R2 buttons. To get this loose, pull the casing outward perpendicular to the L and R buttons until you can slide the L2 and R2 buttons from behind the plastic bar.

    dzturbd - 回复

    SO yesterday replaced the thumb stick on my controller, and now the R2 button is stuck, know any way to remedy this?

    ScootsMcgoots -

    I know you put a warning, but I lost the grey reset button extension. Any idea where to get a replacement part?

    miamiman77 - 回复

    Hey, not even sure when you wrote this, but wanted to share my solution for this problem. I lost one of my reset button rubber pieces when I was doing a different repair, and found that a standard bamboo skewer is just about the perfect diameter to function as a replacement. Just cut it to the proper length and you should be able to get it in there and get your reset functionality back.

    tcbrekke -

    You don't really need it. A long paper clip will work fine.

    Ron Smith - 回复

    I've removed and changed all buttons all seemed ok but now the options and share button don't work, as in when I pressed them down there is no longer a click (bounce) I'm certain it's back in the correct place and I don't think they can be put the wrong way up, does anyone have any advice please :)

    Rachel - 回复

    My share button stopped 'clicking'. When I stripped the controller down I noticed a small copper coloured dimple on the motherboard was depressed instead of proud like the one for the options button. With bluetack I was able to pull it out but each time I tested it with my finger it clicked once and stayed depressed. I don't think there is a permanent solution to this as it's probably metal fatigue or similar so i put a tiny bit of blue tack overy the dimple so the plunger could push that bit further and hopefully pull it out each time. Seems to work as I reassemble the controller. Fingers crossed it holds out a while! I'd love to know if someone else had a different solution.

    The5HD -

    I had an extra part, and it wasn’t gray. Thank goodness for the picture of the black one. It’s rubbery. The small end should be inserted down towards the gold colored spot. It’s next to the word RESET on the mobo.

    J Coyote - 回复

    When reassembling: If, like me, your R2/L2 buttons stayed with the bottom of the controller when you took it apart, it will be impossible to reassemble and get the tiny springs back in place.

    To remedy, remove the buttons, and attach them, with the springs correctly placed, to the top of the controller. There are two tiny grooves, one on the button, and one on the controller top, into which the spring fits.

    Jeff Human - 回复

    Jeff, we owe you a six pack for this comment.

    James Goldie -

    Thank You!! The spring came out and I looked for a way to reinsert it. So I led a thread through its opening (so it couldn´t jump away), and compressed it with pliers. So it was easy to put it in.

    VauWeh -

  3. Spread Fixmas Cheer
    Get $12 off your purchase of $50 or more with code FIXMAS12
    Spread Fixmas Cheer
    Get $12 off your purchase of $50 or more with code FIXMAS12
    • 使用手指来把主板上将控制器两端连接的排线移除

    • 在分离后,将控制器的顶部放在一边。

    添加评论

    • 拆下将组件固定在一起的两个螺丝。 然后使用镊子将图中红色框中的2寸黑色塑料连接器移除。

    • 使用镊子捏住并移除图中标有橙色框的2英寸白色塑料片。

    This is quite different in the latest (JDM-030) versions of the controller. The sub-assembly now clips in, there are no screws, and the black plastic connector is completely absent. The circuit board is also clipped in, no screws.

    marcusharvey - 回复

    • 将透明的塑料片推入,从控制器的顶部取出透明的白色部分。

      • 将透明的塑料片保持在控制器上按下,为充电器端口更换提供空间。

    • 使用Philips#00螺丝刀拧下将充电端口连接到后盖的两个4.0 mm螺丝。

    添加评论

    • 使用镊子将充电口连接到控制器的塑料部分的黑色胶带的移除。

    • 从侧面抓住充电端口的PCB板,缓慢向上拉以从控制器中取出。

      • 不要将蓝色PCB板猛烈向上拉; 而是将组先件一边移动到另一边,以在控制器和PCB之间创建一些空间。

    I have tryed all of this , changed chargers 7× , changed the charging port & still nothing , do you know why & how could I fix it plz , wey thats if its possible lol but tbf I think its going two be best I buy a second hand pad of ebay or go get another original 1 from shop #Sick #HoleInPocketOnesAgain

    Adam Robson - 回复

    I put in a USB charger PS4 is not charging I don't know why

    Tariq - 回复

结论

要重新组装您的设备,请按照本指南的相反顺序进行操作。

64等其他人完成本指南。

特别感谢这些译者︰

100%

Leon赵国鑫正在帮助我们修复这个世界! 想要作出贡献?
开始翻译 ›

Bijan Vakilifathi

于2014年01月21日注册

1,202 信誉积分

撰写一个指南

团队

Cal Poly, Team 6-21, Maness Winter 2014 Cal Poly, Team 6-21, Maness Winter 2014 的会员

CPSU-MANESS-W14S6G21

4 名成员

创作了25篇指南

Where can i get the USB charger part from? mine is damaged so the lightbar and charger doesnt work but it will still connect to my PS4 until the battery runs out.

Matthew - 回复

Did you get it repaired? I need help with mine

Ken Wood -

Where can you get a new DualShock 4 Charging Port Replacement?

Tony - 回复

Have you found them?

jee -

Looking for a new charging port .?

Scott Ruskay - 回复

I cant find charging ports anywhere. . This is becoming a lost cause

jee -

Placed an order with Morbidstix for the charging port. The part was on backorder for four weeks, then Morbidstix refunded my money. It looks like Sony donuts want us fixing our own controllers I guess.

ifixit is out of stock as well.

Nothing on Amazon or Ebay either.

Does anybody know where I can find one of these dual shock 4 charging assemblies?

Nick Hochuli - 回复

my controller war charging until I broke the Mico usb port so I purchased a new one and I can get it to charge at all anytime advice? I've reset it put in a new ribbon and double checked the battery. My controller lights up it just won't charge.

Alan Kane - 回复

My ps4 controller doesn't connect to my ps4 it's says too many usbs are connected

osmanabu66 - 回复

I took apart my controller but the PCB doesnt look like either gen 1 or gen 2 is there a gen 3?

Ray - 回复

Can I charge my P's4 controller with broken socket?

Cristhian Kaiser - 回复

How do I know if I have first gen or second gen? Amazon has the charging ports for sale right now and I need two. My 4 year old tends to force the cable in when the battery is dead and he is mad. :)

Guess I could open one up and look inside. But want to ask anyways. Thanks.

seangardner - 回复

I love ifixit. I have used it numerous occasions. I am not sure why someone would pay $42 to fix a controller issue that may or may not work and you can get a brand new on online for $46.99. I know it's what you guys do and I love it. I just thought I would add my two cents. Thanks.

daniel be - 回复

when replacing the charge port you will need the model/gen number that it is on the part that you will be replacing. mine was JDS-030. disassemble the controller to get to the port and then order the part you need based on the part number and part itself since they are different in size.

Oscar C - 回复

The headphone jack has snaped off inside the dualshock controller of my ps4, tryed a few things off youtube put did not work. can it be repaired or is it time to buy a new one???

JOHANNA COONEY - 回复

if you haven't repaired it or replaced it yet you could try using a very small amount of superglue on a thin stick to attach to the broken headphone jack, give it a minute or 2 to cure and pull it out. make sure not to get the glue on anything other then the headphone jack though

mmmmm -

How do you figure out which usb replacement to buy without opening the controller?

randy barber - 回复

I have changed the charger port on my PS4 pad and I have also put a new battery in the remote and it is still not showing the orange charge light don't know what else to try any ideas?

thanks.

Chris - 回复

Okay repaired 10 minutes

Khalid ibrahim - 回复

How many pins are in the flex cable? Mine is old and the contract pins are broken so I'm getting a replacement.

Jacob Longnecker - 回复

10 pins cable is only meant for the touchpad.

12 and 14 pins cable are used for the USB/lightbar.

14 pins is only used for the 1st gen (JDS-001 only).

12 pins is used for the 2nd gen up to the latest (JDS-011, JDS- 030, JDS-040)

Darth Bidder -

Why is my controller just not turning on, I've already tried resetting it and its been on the charger for about 3 hours

Anthony - 回复

Not accurate for my dual shock controller - a different charging port chip is in place, and no screws are required to be undone to remove the white plastic piece holding the clear plastic cover in place. Also means I need to buy a different chip now that my controller is disassembled, rather than the JDS-011.

Chris Linke - 回复

charger cable was crimped from factory, replaced it using this manual, works great, now what do i do with this $80 new controller i bought and opened..

James - 回复

添加评论

浏览统计数据:

过去的24小时: 81

过去的7天: 442

过去的30天: 2,283

总计 206,339