跳转到主内容

简介

This guide will demonstrate how to replace the battery for the Dell Inspiron 15-7559. This may be necessary if you have issues charging or turning on the device.

For your safety, discharge your battery below 25% before disassembling your device. This reduces the risk of a dangerous thermal event if the battery is accidentally damaged during the repair. If your battery is swollen, take appropriate precautions.

  1. Turn off the computer.
    • Turn off the computer.

    • Disconnect the charging cable from the computer.

    • Failure to turn off the device and disconnect the cable could lead to personal injury or device damage.

    • Flip the computer upside down.

  2. Remove the captive screw located on the top section of the back panel, using a Philips #1 screwdriver. Keep in mind that the screw cannot be fully removed from the panel, even when fully loosened. Keep in mind that the screw cannot be fully removed from the panel, even when fully loosened.
    • Remove the captive screw located on the top section of the back panel, using a Philips #1 screwdriver.

    • Keep in mind that the screw cannot be fully removed from the panel, even when fully loosened.

  3. Use the blue, plastic opening tool to gently pry a section of the back panel open. Next slide the opening tool around the back panel to disconnect the clips holding the panel in place. After the clips have been disconnected, the back panel can then be easily lifted off the computer.
    • Use the blue, plastic opening tool to gently pry a section of the back panel open.

    • Next slide the opening tool around the back panel to disconnect the clips holding the panel in place.

    • After the clips have been disconnected, the back panel can then be easily lifted off the computer.

  4. Locate the battery on the bottom left side of the laptop.
    • Locate the battery on the bottom left side of the laptop.

  5. Unscrew the 5 x 2mm x 5mm screws, using the T8 Torx screwdriver. Unscrew the 5 x 2mm x 5mm screws, using the T8 Torx screwdriver. Unscrew the 5 x 2mm x 5mm screws, using the T8 Torx screwdriver.
    • Unscrew the 5 x 2mm x 5mm screws, using the T8 Torx screwdriver.

  6. Using the tab above the battery, raise the battery far enough to disconnect the cables attached to it. Using your hand grab the white portion connecting the cables to the battery and disconnect it. Do not pull on the cables directly. This would risk damaging them or tearing them from the device.
    • Using the tab above the battery, raise the battery far enough to disconnect the cables attached to it.

    • Using your hand grab the white portion connecting the cables to the battery and disconnect it.

    • Do not pull on the cables directly. This would risk damaging them or tearing them from the device.

  7. Now lift the battery from the device to remove it.
    • Now lift the battery from the device to remove it.

结论

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

9等其他人完成本指南。

Trenton Greevebiester

于2017年10月19日注册

1,488 信誉积分

创作了6篇指南

团队

UW Tacoma, Team S3-G2, Liner Fall 2017 UW Tacoma, Team S3-G2, Liner Fall 2017 的会员

UWT-LINER-F17S3G2

5 名成员

创作了9篇指南

一条评论

Cool, that’s the easy part. How do you tell the UEFI that it’s okay to charge the new battery?

Stefan Bacon - 回复

添加评论

浏览统计数据:

过去的24小时: 4

过去的7天: 41

过去的30天: 186

总计 13,184