修复你的物品 社区 商店

Black and Decker LI2000 Charging Port Replacement

简介

Use this guide to remove or replace the charging port in your Black and Decker LI2000.

你所需要的

  1. Black and Decker LI2000 Charging Port Replacement, Orange Casing: 步骤 1 中的图像 1，3 Black and Decker LI2000 Charging Port Replacement, Orange Casing: 步骤 1 中的图像 2，3 Black and Decker LI2000 Charging Port Replacement, Orange Casing: 步骤 1 中的图像 3，3

    • Remove the following five screws

    • Three 20 mm Phillips #1 screws

    • One 10 mm #000 Phillips screw

    • One 13 mm Phillips 31 screw

    • When you remove the 13 mm screw, the spring may pop out of the screwdriver. Point the backside of the screwdriver away from your face and others.

    翻译

  2. Black and Decker LI2000 Charging Port Replacement: 步骤 2 中的图像 1，1

    • Remove the black sticker with recycling information.

    翻译

  3. Black and Decker LI2000 Charging Port Replacement: 步骤 3 中的图像 1，1

    • Use your fingers or a plastic opening tool to pry the casing apart.

    翻译

  5. Black and Decker LI2000 Charging Port Replacement: 步骤 4 中的图像 1，1

    • Remove the plastic slider by picking it up off the screwdriver.

    • You may consider leaving half of the casing on the screwdriver to make handling the screwdriver easier.

    翻译

  6. Black and Decker LI2000 Charging Port Replacement, Handle: 步骤 5 中的图像 1，2 Black and Decker LI2000 Charging Port Replacement, Handle: 步骤 5 中的图像 2，2

    • Remove the four 15mm Phillips #1 screws.

    翻译

  7. Black and Decker LI2000 Charging Port Replacement: 步骤 6 中的图像 1，2 Black and Decker LI2000 Charging Port Replacement: 步骤 6 中的图像 2，2

    • Use a plastic opening tool to pry the casing apart.

    翻译

  8. Black and Decker LI2000 Charging Port Replacement, Charging Port: 步骤 7 中的图像 1，1

    • Pull the charging port and circuit board away from the casing.

    翻译

  9. Black and Decker LI2000 Charging Port Replacement: 步骤 8 中的图像 1，1

    • Refer to the Soldering Technique Guide to remove the wires at the charging port by heating the existing solder on the contacts.

    • Be sure to keep track of which wire was attached to each lead.

    翻译
结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

作者

与3其他贡献者

Katherine Simmons

于02/08/16注册

732 声望

创作了5篇指南

徽章: 14

+ 11更多徽章

团队

IUPUI, Team 1-3, Baechle Spring 2016 IUPUI, Team 1-3, Baechle Spring 2016 的会员

IUPUI-BAECHLE-S16S1G3

4 名成员

创作了10篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 4

过去 30 天： 9

总计 546