修复你的物品 社区 商店

Battery Disconnect

仅作为前提条件
本指南仅用作其他指南的先决条件。不能单独食用。

简介

prereq battery disconnect

你所需要的

  1. Battery Disconnect, Rear Glass: 步骤 1 中的图像 1，1

    • Before you begin, switch off your phone.

    • Apply a heated iOpener to the rear glass to loosen the adhesive beneath the edges. Apply the iOpener for at least two minutes.

    翻译

  2. Battery Disconnect: 步骤 2 中的图像 1，3 Battery Disconnect: 步骤 2 中的图像 2，3 Battery Disconnect: 步骤 2 中的图像 3，3

    • Secure a suction handle to the lower edge of the rear glass, as close to the edge as possible.

    • If the phone's rear glass is cracked, the suction handle may not stick. Try lifting it with strong tape, or superglue the suction handle in place and allow it to cure so you can proceed.

    • Lift the rear glass with the suction handle to create a gap between the glass and the frame.

    • Insert an opening pick into the gap.

    • If you have trouble, apply more heat to further soften the adhesive. Follow the iOpener instructions to avoid overheating.

    • Slide the opening pick to the bottom right corner of the phone.

    翻译

  3. Battery Disconnect: 步骤 3 中的图像 1，2 Battery Disconnect: 步骤 3 中的图像 2，2

    • Insert a second opening pick and slide it to the bottom left corner to cut the adhesive.

    • Leave the opening picks in place to prevent the adhesive from resealing.

    翻译

  4. Battery Disconnect: 步骤 4 中的图像 1，3 Battery Disconnect: 步骤 4 中的图像 2，3 Battery Disconnect: 步骤 4 中的图像 3，3

    • Insert a third opening pick at the bottom left corner.

    • Start to slide the opening pick from the bottom left corner along the side of the Xiaomi Mi 9 to cut the adhesive.

    • Be aware of the rear cameras and only insert the tip of the opening pick. As the adhesive cools down it gets harder to cut. If necessary use your iOpener to reheat it.

    • Leave the opening pick in the top left corner to prevent the adhesive from resealing.

    翻译

  6. Battery Disconnect: 步骤 5 中的图像 1，2 Battery Disconnect: 步骤 5 中的图像 2，2

    • Insert a fourth opening pick under the top left corner of the rear glass.

    • Slide the opening pick along the top to cut the adhesive.

    • Leave the opening pick in the top right corner to prevent the adhesive from resealing.

    翻译

  7. Battery Disconnect: 步骤 6 中的图像 1，2 Battery Disconnect: 步骤 6 中的图像 2，2

    • Insert a fifth opening pick at the top right corner of the phone.

    • Slide the opening pick along the right edge to cut the remaining adhesive.

    翻译

  8. Battery Disconnect: 步骤 7 中的图像 1，2 Battery Disconnect: 步骤 7 中的图像 2，2

    • Carefully lift the rear glass and remove it.

    • Before installing new adhesive and reassembly, remove any remaining adhesive from the phone, and clean the glued areas with isopropyl alcohol and a lint-free cloth.

    翻译

  9. Battery Disconnect, Motherboard Cover with Charging Coil: 步骤 8 中的图像 1，1

    • Remove the ten Phillips #00 screws (3 mm length) that secure the motherboard cover.

    • There might be tamper proof sticker on some of the screws.

    翻译

  10. Battery Disconnect: 步骤 9 中的图像 1，2 Battery Disconnect: 步骤 9 中的图像 2，2

    • Insert an opening pick at the top right corner of the motherboard cover.

    • Twist the opening pick sideways to pry up and slightly lift the motherboard cover.

    翻译

  11. Battery Disconnect: 步骤 10 中的图像 1，2 Battery Disconnect: 步骤 10 中的图像 2，2

    • Carefully remove the motherboard cover including the charging coil / NFC antenna.

    翻译

  12. Battery Disconnect, Battery Disconnect: 步骤 11 中的图像 1，2 Battery Disconnect, Battery Disconnect: 步骤 11 中的图像 2，2

    • Use a spudger to pry up and disconnect the battery flex cable.

    翻译
结论

To reassemble your device, follow these instructions in reverse order.

作者

与1其他贡献者

Dominik Schnabelrauch

于11/23/16注册

203,362 声望

创作了682篇指南

徽章: 40

+ 37更多徽章

团队

iFixit iFixit 的会员

Staff

135 名成员

创作了16,817篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 0

过去 30 天： 0

总计 67