修复你的物品

维修的权力

商店

Astro A40 TR Speakers Replacement

撰写者： Bhargav Makkapati (和另外2个贡献者)
  • 评论： 2
  • 收藏 0
  • 完成 1

难度

简单

步骤

5

所需时间

15 - 20 分钟

节

1

标志

1

Better Introduction

更好的介绍

通过完成或修改其开头介绍以改善本指南。

  1. To access the speakers you need to disassemble the earpiece. First remove the foam ear piece by simply pinching the padding and pulling lightly until the magnets disengage. To access the speakers you need to disassemble the earpiece. First remove the foam ear piece by simply pinching the padding and pulling lightly until the magnets disengage.

    • To access the speakers you need to disassemble the earpiece. First remove the foam ear piece by simply pinching the padding and pulling lightly until the magnets disengage.

    翻译

  2. Remove the dust cover located on the speaker. Use the corner of the spudger to peel underneath the cover until you can lift it by hand. The cover is held onto the device with adhesive and should be removed slowly. Remove the dust cover located on the speaker. Use the corner of the spudger to peel underneath the cover until you can lift it by hand. The cover is held onto the device with adhesive and should be removed slowly. Remove the dust cover located on the speaker. Use the corner of the spudger to peel underneath the cover until you can lift it by hand. The cover is held onto the device with adhesive and should be removed slowly.

    • Remove the dust cover located on the speaker. Use the corner of the spudger to peel underneath the cover until you can lift it by hand. The cover is held onto the device with adhesive and should be removed slowly.

    翻译

  4. Take off the front cover by removing the four screws located in a square formation on the surface of the device. Use the J00 Philips driver listed in the device page. Take off the front cover by removing the four screws located in a square formation on the surface of the device. Use the J00 Philips driver listed in the device page.

    • Take off the front cover by removing the four screws located in a square formation on the surface of the device. Use the J00 Philips driver listed in the device page.

    翻译

  5. Locate the three small screws under the speaker. Use the J00 Philips Driver to remove them. Locate the three small screws under the speaker. Use the J00 Philips Driver to remove them.

    • Locate the three small screws under the speaker. Use the J00 Philips Driver to remove them.

    翻译

  6. If your issue is asking for the complete replacement of the speaker or the motherboard, un-solder the old components and replace with new speaker by re-soldering.

    • If your issue is asking for the complete replacement of the speaker or the motherboard, un-solder the old components and replace with new speaker by re-soldering.

    • Check out this useful guide on how to solder and desolder connections if soldering is new to you.

    翻译
结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

作者

与2其他贡献者

Bhargav Makkapati

于2016年10月20日注册

156 信誉积分

撰写一个指南

徽章: 8

+ 5更多徽章

团队

UMass Dartmouth, Team 6-5, Martin Fall 2016 UMass Dartmouth, Team 6-5, Martin Fall 2016 的会员

UMASSD-MARTIN-F16S6G5

3 名成员

创作了5篇指南

一条评论

添加一条评论

I’ve found potential replacement speakers here. They look fairly similar to the ones in the A40s, but the resistance value marked on the speakers in the guide vs on the listing is different.

Buyer caution must be taken before actually making the plunge, as sound quality might be different. The listing is from Ali Express after all.

Adrian Kennedy - 回复

添加评论

浏览统计数据:

过去的24小时： 5

过去的7天： 23

过去的30天： 157

总计 4,532