跳转到主内容

修复你的物品

维修的权力

配件 & 工具

简介

不小心掉落了S8?手机和钥匙放在同一个口袋里?

这些情况很可能会导致玻璃后盖破碎。参考本指南以更换三星盖乐世S8的后部玻璃面板。

如果你的更换部件并未包含将其固定的粘合胶,那么你将需要购买用于玻璃后盖及指纹读取器的粘合胶。可以选择专用于S8的粘合胶或薄的高粘合双面胶。

  1. 在S8 的背面较长一端放置加热过的iOpener 大约2分钟。
    • 在S8 的背面较长一端放置加热过的iOpener 大约2分钟。

    • 你有可能要多次加热iOpener以及将iOpener放置在手机上多次来加热下方的粘合剂。 按照iOpener指南来避免过度加热iOpener。

    • 在你等待粘合剂软化的时候,请移步到下一步骤来考虑一下一会从哪撬开手机。

    What type of adhesive should be used to seal? Or better said, what would you recommend.

    Ion Ion - 回复

    I’d recommend precut adhesive designed for the rear cover. If that’s not available, thin, hi-bond double sided tape like 1 mm wide Tesa 61395 tape will work well.

    Adam O'Camb -

    When using a plate to warm things up, at what temp (celsius) should it be to avoid over heating?

    offer423 - 回复

    I cant even get the glass back off it.

    David Corbett - 回复

  2. 接下来的步骤中将切割背面玻璃面板边缘下的粘合剂。 后壳上的粘合剂如第一张图像所示。
    • 接下来的步骤中将切割背面玻璃面板边缘下的粘合剂。

    • 后壳上的粘合剂如第一张图像所示。

    • 从手机外面看到的撬动位置如下:

    • 厚的粘合剂部分

    • 较薄粘合剂的部分

    • 为了保护指纹识别传感器,避免撬动这里。

  3. 一旦后面板摸起来热了,尽量在手机的顶部边缘放置吸盘,同时也要避免放在弯曲的地方。 吸盘不会在玻璃弯曲的地方吸附的很好。
    • 一旦后面板摸起来热了,尽量在手机的顶部边缘放置吸盘,同时也要避免放在弯曲的地方。

    • 吸盘不会在玻璃弯曲的地方吸附的很好。

    • 提起吸盘,在后玻璃面板下插入一个撬棒,或者打开工具。

    • 由于弯曲的玻璃,你需要按照弯曲的弧度向上推撬棒,而不是径直插入到手机里。

    We can't seem to get anything between the edges even after heating the back panel. Any tips?

    Megan Kennington - 回复

    Hi Megan, unfortunately the adhesive is super tough on this one. I’d recommend carefully continuing to apply heat, very gradually so that you don’t accidentally overheat the battery. Eventually you should be able to get a little gap with the suction handle.

    Adam O'Camb -

    I’ve been attempting to get the adhesive to loosen for four hours now. Exactly how much time is this supposed to take? The pictures makes it look like it should be easy. The adhesive still hasn’t budged and I’m beyond frustrated.

    Lori Lucas - 回复

    Hi Lori, sorry to hear the adhesive is being extra stubborn! If reheating and reapplying the iOpener isn’t working, you can try heating the edge with a hairdryer or heat gun. That way you can get more heat onto the edge faster, but be very careful not to overheat the battery inside.

    Adam O'Camb -

    I used a stanley knife - very carefully, after trying for several hours to get the adhesive to loosen. I bought another back cover with adhesive for the assmbley, which is the best option in my opinion. Just be careful not the scratch the case of the phone, and be prepared for the back glass cover to break when removing it.

    James wright - 回复

    The iOpener was a good idea but it just didn’t work. I used the heat gun on low and got it off in about 7 min. 30 min to clean off the excess adhesive. The directions stopped at removing the battery. What the !&&*??? is there a trick to plugging in the battery. Mentioning the need to seat the loudspeaker assembly and the NFC antenna - charging coil would have been helpful. Also, directions on seating the adhesive for the battery. Finally, directions on placing the seal would have been good. I ham handedly got it but needed to use the added adhesive that was sent with the kit. Overall took about an hour. I’m kinda psycho over making sure all the old adhesive was removed. Used the heat gun to reseat backing. worked great! Need to revamp the directions with items above but the kit had everything (except heat gum) and things I didn’t need.(likely to cover other installs.) Worried about breaking glass back but no problem. Thanks for the kit.

    Richard Werbelow - 回复

    The manufacturers really want to make this impossible, huh… I’ve gone 3 years without ever cracking this phone and end up cracking the corner of the back trying to prise it open. Probably should’ve gotten a heat gun too. This is super tight.

    Benjamin Chaim - 回复

    “20 minutes to an hour” is definitely not accurate

    Benjamin Chaim - 回复

    Suction cup just pulls off of the phone, this is pretty useless. Boutta ask for my money back for the kit. I have never had so much trouble with a computer, phones are insanely user-repair-proofed these days.

    Benjamin Chaim - 回复

    I am currently working on this. I have heated the phone to just barely to hot to hold. No matter how many times I've done this and pulled up with a suction cup I cannot get an edge to lift.

    Being that this is my second phone repair does anyone have advice on this? I've watched several YouTube videos and it looks so easy.

    DAVID LAWRENCE - 回复

    I suggest you try to lift on the middle of an edge using the thinnest spudger you have. also as the edge is curved remember to insert it so to follow the curve. Hopes it helps

    Cajuteq -

    Also I'm using a hair dryer.

    DAVID LAWRENCE - 回复

    Our issue was that a small gap would open when using the iOpener, but not large enough to get spudger or opening picks in there (also tried hair dryer but same result). Luckily as a guitar player I had some very thin nylon picks that we were able to get in there, which opened up a large enough gap to get the spudger and opening picks in. From there, we were able to heat the other sides and guide the spudger around the entire edge to get the back glass off.

    First we used a Dunlop nylon .38 mm guitar pick, then a .60 mm pick, and that allowed us to get the spudger in.

    Dan Coleman - 回复

  4. 一旦工具牢牢地插入到玻璃里面后,重新加热iOpener然后将其放置在原位来软化粘合剂。
    • 一旦工具牢牢地插入到玻璃里面后,重新加热iOpener然后将其放置在原位来软化粘合剂。

  5. 任天堂 Switch 套装

    快速恢复到游戏的状态

    购买 Switch 套装

    任天堂 Switch 套装

    快速恢复到游戏的状态

    购买 Switch 套装
  6. 在手机的侧面向下滑动撬棒,来分离粘合剂。 慢慢操作,这样撬棒尖端就不会从缝隙中滑出。如果切割工作变得困难了,请重新加热放置iOpener。
    • 在手机的侧面向下滑动撬棒,来分离粘合剂。

    • 慢慢操作,这样撬棒尖端就不会从缝隙中滑出。如果切割工作变得困难了,请重新加热放置iOpener。

  7. 在手机剩下的边角,重复先前的加热和切割工作 在你切割下一侧的时候请在先前的一侧放置一片撬片,来避免粘合剂重新粘连。 在你切割下一侧的时候请在先前的一侧放置一片撬片,来避免粘合剂重新粘连。
    • 在手机剩下的边角,重复先前的加热和切割工作

    • 在你切割下一侧的时候请在先前的一侧放置一片撬片,来避免粘合剂重新粘连。

    Petite erreur: le guide dit iPhone au lieu de S7 :)

    Nicolas Duthilleul - 回复

    Bonjour Nicolas ! Merci pour la remarque ;-) Nous l’avons prise en compte et corrigé la traduction. La prochaine fois, n’hésitez pas à corriger directement en cliquant sur le bouton Traduire en haut à droite de l’étape.

    Claire Rapp -

  8. 指纹传感器线缆与手机在后玻璃面板靠近主摄像头的位置连接。 这个线缆十分的短,在移除玻璃面板的时候也要断开。 抬起玻璃杯时,请仔查看以确保带有蓝色连接器的橙色电缆已断开连接。
    • 指纹传感器线缆与手机在后玻璃面板靠近主摄像头的位置连接。 这个线缆十分的短,在移除玻璃面板的时候也要断开。

    • 抬起玻璃杯时,请仔查看以确保带有蓝色连接器的橙色电缆已断开连接。

    • 使用打开工具将残留粘合剂分离,小心地打开手机。

    • 如果指纹传感器电缆看起仍处于连接,请勿继续抬起面板,在继续之前请用撬棒来断开连接。

    • 移除玻璃后面板。

    For reassembly, if the fingerprint scanner is removed from the back cover: it’s much easier to place the fingerprint scanner in the small compartment on the back of the phone, connect it and then finally put the replacement back cover on. The adhesive on the inside of the back cover will get connect to the fingerprint scanner and hold it tightly.

    Brian Hoffmann - 回复

    The NFC antenna and coil assembly might get stick to the back cover due to adhesive spreads while trying to pry the back cover to open the phone. Take a look inside to ensure the assebly has not got sticked. If so, try using a credit card like plastic to get it peeled of from back cover without breaking the assembly always paying attention to the fingerprint sensor as well.

    dcode - 回复

    wondering why step 11 speaks of “at least 90% alcohol” and the kit that ifixit sells contains 70% alcohol. #fail

    Jörn Berkefeld - 回复

  9. 在更换后面板之前你需要移除手机上旧的粘合剂。
    • 在更换后面板之前你需要移除手机上旧的粘合剂。

    • 在移除掉旧的粘合剂后,使用用高浓度的异丙醇(至少90%)清洁手机机身的边缘,然后再贴合上新的粘合剂。

    Bonjour,

    Vous parlez d’ajouter de l’adhésif, comment et où le trouve-t-on cet adhésif ?

    Difficile à appliquer ?

    Cordialement,

    Stéphane

    Steph D - 回复

    Mille excuses, je viens de voir les “adhesive strips” :)

    Steph D - 回复

    I broke the rear glass trying to get all the adhesive off! Be very careful!!

    jimhunz - 回复

  10. 重新加热iOpener然后将其放在后玻璃指纹传感器上。 推动指纹传感器,来使其与后面板上的粘合剂分离。 如果传感器很难卸下,请轻轻地将一个塑料打开工具放置在塑料背衬的下方,以便在推动之前松开粘合剂。
    • 重新加热iOpener然后将其放在后玻璃指纹传感器上。

    • 推动指纹传感器,来使其与后面板上的粘合剂分离。

    • 如果传感器很难卸下,请轻轻地将一个塑料打开工具放置在塑料背衬的下方,以便在推动之前松开粘合剂。

    • 这样做可能损坏粘合剂无法重复使用,所以请先尝试第一种方法。

  11. 如果指纹传感器粘合剂完好无损,可以被重新使用,但如果损坏,您应该去除旧的粘合剂并贴合上新的。
    • 如果指纹传感器粘合剂完好无损,可以被重新使用,但如果损坏,您应该去除旧的粘合剂并贴合上新的。

    • 取出旧粘合剂后,用高浓度异丙醇(至少90%)清洁指纹传感器的边缘,然后涂上新的粘合剂。

结论

黏好粘合胶后参考下列步骤的相反顺序重新组装你的设备。

97等其他人完成本指南。

特别感谢这些译者︰

100%

这些翻译人员帮助我们修复这个世界! 想要作出贡献?
开始翻译 ›

Sam Goldheart

于2012年10月18日注册

414,203 信誉积分

创作了547篇指南

团队

iFixit iFixit 的会员

Community

126 名成员

创作了11,842篇指南

Will the phone still be water proof after this

gavinjay - 回复

No. After the adhesive is removed, your water resistance is as gone as your warranty.

James watling -

after the rear panel is removed? ... no...

John Joiner - 回复

Nice its simple action with this tutrial

Seibors - 回复

Could I apply tesa tape 1mm to the sides then would it become water resistant like ip 68.

Darrell Ross - 回复

Great tutorial, simple and straight to the point. My type of learning.

If I could add just one little thing….

I myself would have loved if you would have touched on replacing the fingerprint scanner ribbon when replacing the back glass. , I learned

None the less, you gave me knowledge and I thank you…

Alvin Thomas - 回复

it will be if you do the process 100% correctly and ensure a proper seal by applying enough adhesive at the edges (yet not too much!) at the edges and around the camera and fingerprint scanner. In theory that should do it, but bear in mind i have not tested this

Robin Bogaards - 回复

Where to buy original rear back glass?

a.voloshin - 回复

Under “parts required”, I see:

Galaxy S8 Rear Glass Panel - $90

Galaxy S8 Aftermarket Blank Rear Glass Panel $15

1. I assume I only need one of these parts, correct?

2. if correct, what’s the difference between the two? they look like the same exact part, except the $90 is Samsung branded and the non-branded is $15

Thanks everyone!

Jimmy Ng - 回复

That is correct. The non-branded one is generic. The one that says “SAMSUNG” is name brand and just costs more. You can use either one.

Albert Ayala -

This tutorial’s “items needed list” is missing the fingerprint sensor’s adhesive gasket, which you guys carry, and is therefore incomplete. please correct this. I missed this and ended up with needing to make two carts, one specifically for the gasket.

The tutorial was very good otherwise. thank you for making it.

Jasper Davis - 回复

Will the phone still waterproof if you replace a new back glass panel?

J Brmdz - 回复

What adhesive do you use ? can you recommend ? I bought one that already had adhesive on the back panel but one side raised up slightly, I could get my finger nail underneath and the gap was noticible.

Links to product would be great.

Thanks

Dave

dave - 回复

Hey Dave a the top of the guide we list the rear cover adhesive you can find in our store!

Sam Goldheart -

Thanks for the guide, was handy. Definitely needs glue to hold the new cover, fingerprint sensor and the other bit on - just ordered a B-7000.

drpotatoman - 回复

very hard and difficult to pass the spudger under the glass !!! But I didn’t abandonned I did it! thanks for the share.

SAINTE-COLOMBE Vonjy - 回复

I have learned my lesson! Edge dropped phone. Display cracked , force created a hidden micro crack in the back glass. I heated the back very well, but still that thing cracked as I was finishing. Take my advice, and anytime you work on this phone buy a new back, then just break off the current one. You will be sooo much happier. Don’t forget to make sure it comes with adhesive.

Max Reynal - 回复

I have recently tryed to chainge my screen but the one i have taken off has a tint on it where my replacement screen is clear do i have to purches the tint separately or have i just orderd the wrong one i have a samsung s8 galaxy

Steve Tout - 回复

添加评论

浏览统计数据:

过去的24小时: 73

过去的7天: 472

过去的30天: 2,136

总计 271,189