简介

本指南旨在更换耳机扬声器组件。该组件包含了一个扬声器,话筒,红外线发射器以及环境光线传感器。

本指南涉及到拆卸后部玻璃面板。拆卸后部玻璃面板需要去除将其固定到位的粘合剂。参考 本指南以重新安装后部玻璃面板。

将回形针或SIM卡针插入和电源按钮同侧的SIM卡槽的孔中。
  • 将回形针或SIM卡针插入和电源按钮同侧的SIM卡槽的孔中。

  • 按压回形针或卡针,使得SIM卡槽弹出

    • 大力按压可能损坏你的SIM卡卡托

添加评论

将SIM卡托从手机中移除
  • 将SIM卡托从手机中移除

添加评论

  • 在操作前我们推荐你清空微波炉,在底部的任何讨厌的食物残渣最终都可能粘在iOpener上。

  • 把iOpener放在微波炉中间 。

    • 对于旋转式微波炉:确保盘子可以自由旋转。如果你的iOpener卡住了,它可能会过热并燃烧

which temperature must be used for heating? Thx

fbarletta - 回复

I found you need to be very patient when using the iOpener. It's worth taking your time, giving the heat time to work on the glue. When I finally got the battery out, there were some strips of glue left behind that I just cleaned off with some isopropanol before installing the new battery.

By the way, I had to run the iOpener for longer in my microwave for it to get hot enough. When it was too hot to touch, I figured it was hot enough for the batteries.

Fredrik -

I didn't find this to be as hard as I had built it up in my mind to be; HOWEVER, saying that I need to say years ago I was the local Nokia service center in my town. But many years ago right after they got rid of analog times. Yeah. A classic installer/repairer mistake when starting something they haven't fixed or installed before is picking up the instructions, flipping through them; maybe even reading a section that is new-then tossing the instructions over the shoulder. "I got this." This usually comes right before something major gets broke. And I can tell you when you try to do it yourself and then mess it up horribly then take it to the repair shop. Well we called that "I can do it myself" syndrome and charged extra to put back together what they brought in in the box. Now knowing all this - I can't stress this enough because I am stupid, stupid, stupid. COVER YOUR SCREEN IN CLEAR BOXING TAPE AND READ ALL THE INSTRUCTION BELOW THROUGH TO THE END BEFORE EVEN ATTEMPTING THIS FIX. Take my advise.

windizy - 回复

I didn't have an iOpener, so I used a wheat type heat bag. If you do this though, make sure you put a layer of plastic between your Mac and the bag, or you'll get condensation in places you don't want it.

Martin Gray - 回复

I started out using the iOpener but switched to my wife's hairdryer. A heat gun or hair dryer proved to be much more convenient and is a time saviour. You can heat more and the glue becomes more fluid make the next steps with the opening picks much easier

Jan Van Puymbroeck - 回复

Use a hair dryer! Watch this vid: https://youtu.be/16GkvjVyOJA It is much easier to do if you heat it from the other side.

Fletcher Carpenter - 回复

I wonder how many people actually wrapped in their iPhone into iOpener and put this "sandwich" into microwave??

putinaspiliponis - 回复

I know this is obvious, but backup your iPad with iTunes before you start. I'd also turn off your passcode if you have one.

Laurie Higgins - 回复

Ther first time you heat up the iOpener for this repair when its room temperature I had to heat it up for more than 30 seconds. I remember I had to heat it up for around 45 seconds. However, after that when you need to reheat it again during the repair 30 seconds will be enough.

Yousef Ghalib - 回复

I've been with Samsung for 8 years now!! Never did i have a case on any of my phones My Samsung 8 is 2 months old the case protector around the edge pop off and broke my phone it's like someone put a bullet hole in it

Sherry Carew - 回复

Not everybody has a microwave. You need to state how long and at what temperature in a conventional oven.

Esmond Pitt - 回复

Hi, the microware have multiple power 1 to 9, what must be used ?

Regards,

Cedric

Cedric VINCENT - 回复

  • 加热iOpener三十秒

  • 贯穿整个维修过程,如果iOpener 冷却了,在微波炉中每次重新加热额外的三十秒。

  • 注意在维修过程中不要过度加热iOpener,过热可能会导致iOpener爆炸。

  • 如果出现膨胀千万不要碰iOpener。

  • 如果iOpener中间部分依然烫的没法碰,请等待冷却后再加热,一个加热好的iOpener 应该可以保持热度十分钟

May I know the temperate limit about heating iOpener? (maximum 150 degrees Celsius?) thx so much.

yamayhuang - 回复

I had to heat mine up for more than 30 seconds. After 30 seconds on high it was only warm. It had to keep trying different times and checking it until it got hot. I think the initial time that I put it in for was over a minute.

whale13 - 回复

DO NOT USE IN NON ROTATING MICROWAVE! It will pop a hole. I had it in for 45 seconds the first time. It wasn't very hot inside and I saw it started to leak on the paper towel I put under it. Just a fair bit of advice. I think I will just stick with the heat gun. Loud but useful.

Alex Jackson - 回复

I don't own a microwave.

mdanihy - 回复

Its again waterproof when you change iphone 7 battery?

Jon - 回复

I don't have a microwave???

Joe Blow - 回复

30 sec at which equivalent watts setting and what temperature does iOpener heats up to for 30 secs. Only just bought it so needs info before using it. Thanks

Sam Stieg - 回复

can i use just ordinary microwave???

juneseok kwon - 回复

If I don't have a microwave then I try to use hot air gun so how many munuts i want to heat ?

Mohideen Rifay - 回复

I heated mine up for 30 seconds, tested, then again for 30 seconds. It felt adequately hot. Leaving it on the left side, per the instruction, for a minute did not loosen the adhesive. I ended up pulling the suction cup hard enough to shadder the old screen. Moral of the story, I don't think it gets hot enough safely to have an affect.

Travis Dixon - 回复

There is a clear problem here with the heating part using the iopener things....no details are given. Whoever is testing them needs to make it clear - What temperature does it need to be? And for which phone models, because they differ in what's needed. It's only £10-15 for a laser guided temp sensor unit, and the designers/repairers should have one of those already for doing these kinds of repairs. Explaining half a repair, is worse than not explaining at all :-(

assortedrubbish - 回复

I used a hot water bottle, works well as it covers the whole screen and stays hot for longer.

dave - 回复

If I may suggest include your microwave wattage so people can get an idea on time for there own

Patrick Storey - 回复

I ended up using a hair dryer. That iOpener thing took forever.

mark fitzgerald - 回复

30 seconds sure isn’t cutting it… 45 didn’t get the screen of my iPad air 2 to budge either… even after resting on the ipad for 4 minutes.

60 seconds in the microwave, the iOpener burst.

I’ll get a new one and try once more with heating it 45 seconds and repeat that for 30 minutes like others have said here. If that doesn’t work it’ll have to be the heat gun.

K

Karl Marble - 回复

  • 把iOpener从微波炉中拿出来,捏着两边扁平边缘中的一个避免碰到中心热的部分。

  • iOpener会非常烫,所以拿着它的时候千万要小心。必要的时候可以使用烤箱手套。

Will a hair dryer work for heating the glass?

Me berg - 回复

Yes, as does a heat gun.

anonymous 4602 - 回复

I did this repair. I used a hair dryer, I think it works better: gets very hot fast.

Cobus de Beer - 回复

  • 将你的手机正面朝下放置。

  • 如果手机的玻璃面板已经碎裂,请在拆卸过程中用胶带固定住整个面板。

  • 将iOpener放置在面板上约60秒以融化固定玻璃面板边缘的封胶。

  • 移动iOpener以加热剩余部分的面板,同样需要60秒。

  • 吹风机,热风枪,或者加热工具也许都会用到,但是千万不要过度加热手机——OLED 屏幕和内部电池都会容易热损坏。

are there any option out there that allows you to heat the adhesive outdoors without any power plug?

Brotan Store - 回复

There's a star in the center of our solar system, you could try that.

John Joiner -

the way we do it at Get it fixed cellphone repair calgary is with a heat gun, wich is way easier than this, make sure to wear some gloves and dont worry to use to much heat as long as you point just to the back of the phone, (the back panel is thick enough to protect the logic board from over heat) instead of the usual blue plastic piece i sugest to use the thinnest metal razor knife and a business card so you can insert the business card and move it all around the frame, those blue plastic things are way too thick that will break the glass panel if you apply to much pressure

get it fixed - 回复

After did that with my own heat pad, the white paint got ripped off but luckily glass back cover did not break. So I scratched all white part of the back cover and now its all transparent.

Jae Chung - 回复

I used a purpose built heating device at 100 degree celsius. Lower temperatures didn't work.

ken - 回复

  • 将吸盘紧紧吸在后部玻璃面板的下部。

If the rear screen is cracked/smashed, you will not be able to use a suction cup to remove it. The suction could would not seal because of the cracks. I tried masking tape, 3M shiny HVAC tape, and others, and the suction could would not seal to those surfaces either.

I ended up using the sharp point of the smudger to remove some shards of glass to get underneath the cover to leverage it up and out. Definitely use gloves and safety glasses if you have to do this.

dougpender - 回复

Thank you for your comment. I needed to see this particular instance of what to do when the back cover was cracked. I was going to try to suction it with tape covering it. This saved me some heartache. You're an angel!!

Jessie Brooks -

  • 本步骤还使用了一个塑料撬片,用来将后部面板从中框分离。如果双面胶的粘性仍然很强,用iOpener再加热一次。

  • 使用吸盘在面板中部用力,旋转你的手腕向上拉后部的边缘。

添加评论

  • 当你打开一个够大的缝隙后,在后部玻璃面板和中框之间插入一个塑料撬片。

At this stage I didn’t use a plastic pick as I think they are too thick and will crack a screen that’s not already cracked. I used a stainless steel

I sesame blade which does a much better job of cutting through the adhesive. Just be careful not to insert it in too far. I sometimes put a mark on my blade to ensure it doesn’t go in too far.

Wayne Lyell - 回复

  • 将塑料撬片绕后部玻璃面板的底部左侧滑动。

添加评论

  • 将塑料撬片沿着手机的电源按钮一侧滑动。

添加评论

  • 将塑料撬片沿着手机顶部滑动。

添加评论

  • 将塑料撬片沿着手机的音量按钮的一侧滑动。

添加评论

  • 按住中框,向上拉后部玻璃面板将其与组件分离。

    • 如果由于双面胶粘性太强,用塑料撬片在玻璃下面滑动数次。

添加评论

  • 在后部面板和中框之间插入塑料撬片。

  • 沿着手机的顶部滑动撬片以清除剩余双面胶。

  • 扭动撬片以分离两部分。

添加评论

  • 此时,后部玻璃面板应该完全从手机上分开。双面胶可能仍然会粘附在两侧上。

  • 拉开后部面板,然后完全分离它们。

  • 参考此指南以重新安装后部玻璃面板。

You should note that the adhesive strip may need to be fully removed from the frame in order to proceed with repairs. The adhesive on my phone covered all of the screws exposed in the next step.

Sean Cruz - 回复

  • 卸下13个3.5毫米用来将中框固定在手机上的Phillips #00螺丝。

Make sure you do not mix up these thirteen screws with a hidden 14th screw under the mid-frame chassis, on the left side of the headphone port, on daughter-board. This 14th screw is shorter than the other screws, so make sure you do not replace it with one of the longer screws. It will push up against the front glass and lift it away from the adhesive.

David Whyte - 回复

  • 紧紧地抓住中框组件的边缘。

  • 向下推电池的同时抬起中框组件,以将其与手机的剩余部分分开。

FIRMLY GRASP IT! - Patrick

Armen Orbelyan - 回复

Bei diesem Schritt sicher sein, dass SIM Card Fach entfernt ist!

zikal - 回复

I found the glue still very sticky here, i had to go around with my picks to free it, its very stuck with a UK version, beware!!

databeat1 - 回复

I damaged my screen here a bit, be careful not too slide your pick between the digitizer and the screen.

Anton -

i suggest to apply heat on the corners of the front screen to lose the adhesive a lil bit and push from the bottom back of the phone right where the wireless charger is because of the charging port

get it fixed - 回复

When grabbing from the bottom, you fun the risk of damaging the charging port and headphone jack. I would suggest starting from the top. This is because the two ports at the bottom slide down into the frame. There is also adhesive that will give you a little resistance.

Alex Philip - 回复

Step 18 is not correct, you have to start from the top. You can damage the charge port

Daniel Yaben - 回复

On mine the adhesive actually tore away part of the colored film on the back of the screen glass rather than separating from it. I’m guessing applying heat to the screen corners first would help avoid this (I didn’t). https://imgur.com/a/V7vZQ

Brian Hardie - 回复

  • 抬起中框将其与手机的剩余部分分离。

what do the numbers ZF-N2 AS WELL AS (F13) AT THE END OF THE MODEL NUMBER, THEN THERE IS REV 5-1-C W G 15221............... WHAT ALL HAS TO MATCH WHEN REPLACING THE MID FRAME.

mike gentry - 回复

  • 使用撬棒的平端从主板的插座上断开电池的连接器

添加评论

  • 使用撬棒将听筒扬声器组件从显示器框架上撬开。

添加评论

  • 撬松后使用镊子小心取下该组件。

  • 该组件包含了扬声器,话筒,红外线发射器以及环境光线传感器——它们均处于不同的PCB板上。确保每个元件均松开后再将整个组件撬起并取下。

添加评论

结论

请按逆序重装你的设备。若要重新组装后部玻璃面板,参考重新安装后部玻璃面板粘合剂指南。

2等其他人完成本指南。

特别感谢这些译者︰

100%

Yuting Zhao正在帮助我们修复这个世界! 想要作出贡献?
开始翻译 ›

Dante Mazzanti

于2015年07月13日注册

30,222 信誉积分

创作了26篇指南

添加评论

浏览统计数据:

过去的24小时: 3

过去的7天: 28

过去的30天: 147

总计 855