Whirlpool Wric 3c26 Error Code 10 - 2 / flashing light + number 3

Question

Whirlpool Dishwasher

Repair information for Whirlpool dishwashers.

157 个问题查看全部

Maroš Ondruš @marosondrus

声誉积分: 11

1

发帖于: 2023年4月17日

更多选项

Whirlpool Wric 3c26 Error Code 10 - 2 / flashing light + number 3

Good day, I would like some advice regarding the dishwasher (brand above). The dishwasher stopped draining water, if I remove the water manually, the dishwasher starts the program and after a few minutes the cycle stops. If I turn on the dishwasher even with water inside, it just beeps and the start light flashes quickly and the display shows the number 3, if I put the dishwasher in diagnostic mode, the start light flashes 10 times and the display shows the number 2. Can anyone help me, what could this be? ? I cleaned the drain and the filters. I am concerned that it will be the pump or something related to it (stuck, stopped working). I will be grateful for any advice. Thnx

已回答！ 显示答案我也有这个问题

这是一个好问题吗？

是否

得分 0

添加一条评论

1个答案

已选择的解决方案

jayeff @jayeff

声誉积分: 453千

11

368

1.4千

发帖于: 2023年4月17日

更多选项

Hi @marosondrus ,

Here's some info that may help or maybe not.

Here's a link that shows that the error (#3) may be a problem with the heater or heater circuit or perhaps the temperature sensor (examples only to show what they look like and how much they may cost).

Fault diagnostic code of 10 flashes also indicates a sensor problem.

Hopefully this is of some help.

Unfortunately I can't find a service manual or a wiring schematic which would make it easier to test them using a meter.

这个答案有帮助吗？

是否

得分 2

6条评论:

I'm at work at the moment, but when I get home, I can easily take pictures and add them here, because I seriously don't know what it means anymore, I don't understand why the water doesn't drain, or if the sensor has any effect on the fact that the water remains in the dishwasher. I looked at the site, but most of the errors are described in F(X) codes.

由 Maroš Ondruš 完成的 2023年4月18日

https://beko.elektrahk.cz/482000032666-c...

由 Maroš Ondruš 完成的 2023年4月18日

@marosondrus

It might be that it isn't even starting because the water is not hot enough, therefore it won't drain after filling etc

Here's how to easily add images to your question on ifixit 在已经存在的问题里加入图片

With the power disconnected from the dishwasher you should be able to use an Ohmmeter and check both the sensor and the heater for continuity. They should not test open circuit.

Unplug them and test directly across their connection terminals.

由 jayeff 完成的 2023年4月18日

As I wrote above, if I manually remove the water from the dishwasher, the cycle and the program start to work, then it works for about 20 minutes, the water is heated, but then it stops and stops working and the water is not pumped out. I think the heating is fine, but probably the sensor is not... But that's just my theory, it doesn't matter at all in these machines. And thanks, I'll try to take pictures of the problems after lunch.

由 Maroš Ondruš 完成的 2023年4月18日

I have no idea what's happened, but I tryed again same Diagnostic Code (Start, 2x Program Button, Start, 2x Program Button, Start), now and water was suddenly drain out. Also I tryed rinse Program and everything went fine. Can someone explain me what's happened, because actually I really don't understand, I tryed IT Yesterday few times and nothing happen.... But anyways Thanks You man for your time.

由 Maroš Ondruš 完成的 2023年4月18日

显示更多的1条评论

添加一条评论

I'm at work at the moment, but when I get home, I can easily take pictures and add them here, because I seriously don't know what it means anymore, I don't understand why the water doesn't drain, or if the sensor has any effect on the fact that the water remains in the dishwasher. I looked at the site, but most of the errors are described in F(X) codes. — Maroš Ondruš
@marosondrus

It might be that it isn't even starting because the water is not hot enough, therefore it won't drain after filling etc

Here's how to easily add images to your question on ifixit 在已经存在的问题里加入图片

With the power disconnected from the dishwasher you should be able to use an Ohmmeter and check both the sensor and the heater for continuity. They should not test open circuit.

Unplug them and test directly across their connection terminals. — jayeff
As I wrote above, if I manually remove the water from the dishwasher, the cycle and the program start to work, then it works for about 20 minutes, the water is heated, but then it stops and stops working and the water is not pumped out. I think the heating is fine, but probably the sensor is not... But that's just my theory, it doesn't matter at all in these machines. And thanks, I'll try to take pictures of the problems after lunch. — Maroš Ondruš
I have no idea what's happened, but I tryed again same Diagnostic Code (Start, 2x Program Button, Start, 2x Program Button, Start), now and water was suddenly drain out. Also I tryed rinse Program and everything went fine. Can someone explain me what's happened, because actually I really don't understand, I tryed IT Yesterday few times and nothing happen.... But anyways Thanks You man for your time. — Maroš Ondruš

Whirlpool Dishwasher

Whirlpool Wric 3c26 Error Code 10 - 2 / flashing light + number 3

1个答案

添加你的答案