Speed control lever won't stay in off position

Question

KitchenAid KSM150PSER

KitchenAid's Artisan Series 5 Quart Tilt-Head Stand Mixer model number KSM150PSER. All models starting with KSM150PS are the same device just different colors.

20 个问题查看全部

BigD McC @bigdmcc

声誉积分: 1

发帖于: 2020年4月13日

更多选项

Speed control lever won't stay in off position

I have an Artisan KA about 9 years old. It has done well but over the last few months the speed control lever has started to jump out of the off position so that when you switch the power on at the mains it starts from speed one. I’ve taken the back off, and the adjustment screw wasn’t all the way in - but if I screw that in then it forces the main contacts apart until the lever moves to position 3. It feels like the lever needs more upward pressure, so that the raised bump on top of the lever is pushed more firmly into the grooves carved into the side of the body (they are hidden under the thin aluminium strip that wraps round the machine). Anyone got any ideas? Many thanks!

已回答！ 显示答案我也有这个问题

这是一个好问题吗？

是否

得分 0

添加一条评论

2个答案

已选择的解决方案

Finkerbell @finkerbell

声誉积分: 127

3

发帖于: 2020年5月30日

更多选项

Your analysis is correct. The “bump” needs to better engage. This is best done by opening the machine up and 1) making sure the pivot screw holding the lever in place is not loose, and 2) if needed, remove the lever and give it a slight bend in the right direction, and reattach.

Then re-adjust the mixer speed per the instructions in:

++http://www.kitchenaidparts.eu/documents/...

这个答案有帮助吗？

是否

得分 2

3条评论:

Thanks Finkerbell. I had decided to open the whole thing up anyway, and your first solution above was exactly what fixed the issue - the screw holding the lever in place needed a half turn to tighten it up. Thanks for responding!

由 BigD McC 完成的 2020年6月2日

It’s a poor design. The lever pulls a spring which moves a lever to adjust speed. The spring is under max tension when off. The only thing holding the lever off is a very small tooth in a tiny groove. They both need to be bigger. For such a good brand this is like a 1950’s design.

I took mine apart and found the lever was also slightly bent down. I straightened it then used a dremel to make the grooves larger. It helped but doubt it will fix it for good.

由 Mark Misky 完成的 2020年11月21日

Helpfull but link to instructions has two extra + characters at the end that cause an error. I used http://www.kitchenaidparts.eu/documents/... which worked.

由 Ed Almquist 完成的 2023年12月26日

添加一条评论

Thanks Finkerbell. I had decided to open the whole thing up anyway, and your first solution above was exactly what fixed the issue - the screw holding the lever in place needed a half turn to tighten it up. Thanks for responding! — BigD McC
It’s a poor design. The lever pulls a spring which moves a lever to adjust speed. The spring is under max tension when off. The only thing holding the lever off is a very small tooth in a tiny groove. They both need to be bigger. For such a good brand this is like a 1950’s design.

I took mine apart and found the lever was also slightly bent down. I straightened it then used a dremel to make the grooves larger. It helped but doubt it will fix it for good. — Mark Misky
Helpfull but link to instructions has two extra + characters at the end that cause an error. I used http://www.kitchenaidparts.eu/documents/... which worked. — Ed Almquist

Edward @efgabrielle 声誉积分: 1 · Answer 1 · 2021-11-24T20:31:21-07:00

Edward @efgabrielle

声誉积分: 1

发帖于: 2021年11月24日

更多选项

My mixer would intermittently turn on in the off position. I took the back cover off and found a set of points that should be open when in off position on the speed control board. I gently opened the points very slightly so they had a perceptible gap when off. I set the indicator to position 1 to make sure they did make contact in that position. Problem solved.

这个答案有帮助吗？

是否

得分 0

添加一条评论

KitchenAid KSM150PSER

Speed control lever won't stay in off position

2个答案

添加你的答案