修复你的物品 社区 商店

iPhone4S是第五代iPhone。网络制式为GSM/CDMA ，存储容量有8GB、16GB、32GB、64GB可选，机身颜色有黑色、白色可选。维修iPhone4S是容易的，需要耐心，用到的工具有螺丝刀、撬棒等。

2193 个问题 查看全部

更多选项

Logic Board Dead - Possibly Fried After Water Damage

Hello.

I'm 14 and have been repairing iPhones for just over a year now. My cousin was on holiday just before christmas in the Caribbean. She bought a waterproof case from Apple and was taking photos In the sea. I'd seen previous results and they were very good. However, on the last day the case let sea water in. She contacted me when she was home, I told her not to try and switch it on or to charge it, but she had done both on holiday in panic. Apple have confirmed they will replace the phone but there are many valued photos etc on the phone. Taking it apart, corrosion near the bottom was bad. Removing the battery removed one of the four pins for the battery connector. I scrubbed the board clean with a toothbrush and IPA. It's cleaned up well, and looks normal apart from the battery connector. Earlier today I removed the 3 removable logic board shields and searched for damage. I can't see any burn marks etc? got a new dock and screen and tried to power up the device using a charger without the phones battery, but the phone remained dead. It didn't connect with iTunes but I don't know if re assembling the phone to put it into dfu mode would make iTunes recognise it? I'm waiting for my dad to get me some more IPA and I will soak the logic board in an ultrasonic bath. Can anyone help me, any advice to why it won't come on? is it completely dead?

Thanks in advance, Sam.

已回答！ 显示答案 我也有这个问题

这是一个好问题吗？

是 否
得分 2
2条评论

Power issues are not fixed by blindly trying, but testing.

Which pin of the connector did you remove?

由完成的

With the logic board sitting the right way up, as if it was in the phone, it's the top pin. I know this is important but I thought I could still get power into the phone?

由完成的

添加一条评论

2个答案

筛选条件:
最有帮助的 最新 最老的
已选择的解决方案

更多选项

Sam--my advice is to send the board out for battery connector repair--it's about $20-30 on eBay and very straightforward if you have experience.

You will certainly fail, like we all did, the first time you try it. This phone has a high likelihood of having salvageable data, so you might not want it to be your test case.

If you insist, the battery connector repair is done under the microscope with flux and a soldering iron. Hot air will melt the connector. There are all sorts of tips that you learn just from experience--in the first me I did, I couldn't understand why pad #1 and #4 (+ and Gand) were like mud, while solder flowed fine on the other pads. I assumed it just needed more heat, and ended up knocking off tiny components that I had to replace later--and didn't have the equipment or skills to do that either. Fast forward a few months, and now the job takes about ten minutes tops.

Good luck

Jessa

这个答案有帮助吗？

是 否
得分 2

3条评论:

Thanks for your advice. Going to attempt this repair myself as I need to start somewhere! My dad has a lot of experience soldering and creating pcb that are as compact as the iPhones logic board. I'll make sure to post my results! Thanks again

由完成的

Hello.

I have attempted the repair. new battery connector is soldered down but the phone is stuck at the apple logo, before shutting down and switching on again, in a loop. How do i fix this? thanks

由完成的

that is a typical symptom of a failed battery connector repair--check for continuity across the pos and neg battery pins (the far left and far right). you should not hear a beep. Check between the gnd pin and gnd (any part of the shield) you should hear a beep. Check between the pos pin (closest to the main part of the board) and the copper dots nearest that pin--you should hear the continuity beep there.

If you have access to a direct current power supply, connect a lead directly to the pos and neg battery pins on the board and see if the phone will turn on as normal.

There are other ways to get stuck in a boot loop, but in this case, failed battery connector repair is most likely.

由完成的

添加一条评论
最有帮助的答案

更多选项

The top pin is BATT VCC, it supplies electrical power for the entire phone. Cell phone logic boards are usually designed to be only powered on with functioning batteries attached. Simply plugging the charger in would not work

这个答案有帮助吗？

是 否
得分 2

6条评论:

What do I need to do to get the phone to work then? just replace the battery connector?

由完成的

Of course you should try this first

由完成的

can you give me any advice on doing this? never done this before. What equipment should I use? soldering iron or hot air rework station??

由完成的

This is probably too hard for you now. Hot air rework station should work but it is really easy to mess things up. If you decide to do the repair yourself, you should practice on some junk boards first, to learn wow to use the tool properly without causing addictional damage or injury. Iphone boards are very compact and difficult to work on, so more practice than other usual repairs are needed.

由完成的

What other tools do I need? A flux pen? do I need any type of tape for heat protection?

由完成的

显示更多的1条评论

添加一条评论

添加你的答案

Sam Murphy 将永远感激不已
浏览统计数据:

过去 24 小时： 0

过去 7 天： 1

过去 30 天： 1

总计 18,952