修复你的物品

维修的权力

商店

Sony Xperia Z5 Teardown

撰写者： Lenka (和另外3个贡献者)
发布于： November 6, 2015
  • 评论： 26
  • 收藏 30
  • 浏览量 125.5千

拆解

在此拆机指南中使用的工具

购买这些工具

视频概述

简介

This guides will show you how to disassemble Sony Xperia Z5.

这个拆解是不是维修指南。 要维修你的的Sony Xperia Z5，请使用我们的维修手册。

  1. Remove SIM card tray. Remove SIM card tray.

    • Remove SIM card tray.

    编辑

  2. Heat the back cover to soften the adhesive. Place the suction cup and insert metal opening tool to open a gap from top side.

    • Heat the back cover to soften the adhesive.

    • Place the suction cup and insert metal opening tool to open a gap from top side.

    编辑

  3. Insert the guitar picks and slide it to cut the adhesive underneath. Remove back cover. The back cover is glass, so only use a sucker if you're experienced. otherwise use a small blade to lift off the back while the glue is soft. Remove back cover. The back cover is glass, so only use a sucker if you're experienced. otherwise use a small blade to lift off the back while the glue is soft.

    • Insert the guitar picks and slide it to cut the adhesive underneath.

    • Remove back cover. The back cover is glass, so only use a sucker if you're experienced. otherwise use a small blade to lift off the back while the glue is soft.

    编辑

  4. Release battery connector and pull off the adhesive tape underneath. Pry up battery. Pry up battery.

    • Release battery connector and pull off the adhesive tape underneath.

    • Pry up battery.

    编辑

  5. Release rear camera connector, front camera connector, audio jack flex connector and main flex connector on the motherboard and remove the screws there. Take away the plastic bracket. Take away the plastic bracket.

    • Release rear camera connector, front camera connector, audio jack flex connector and main flex connector on the motherboard and remove the screws there.

    • Take away the plastic bracket.

    编辑

  6. Remove metal cover securing loudspeaker and twist off screws. Pry up and loosen the bottom side of main flex assembly. Pry up and loosen the bottom side of main flex assembly.

    • Remove metal cover securing loudspeaker and twist off screws.

    • Pry up and loosen the bottom side of main flex assembly.

    编辑

  7. Essential 工具包

    我们最紧凑的套装中最有用的工具。

    现在开始购物

    Essential 工具包

    我们最紧凑的套装中最有用的工具。

    现在开始购物

  8. Remove main flex. ( Attention: the fingerprint sensor connector is here, be careful to loosen it) Remove main flex. ( Attention: the fingerprint sensor connector is here, be careful to loosen it)

    • Remove main flex. ( Attention: the fingerprint sensor connector is here, be careful to loosen it)

    编辑

  9. This is main flex assembly. (It comes with loudspeaker and vibration motor ) This is main flex assembly. (It comes with loudspeaker and vibration motor )

    • This is main flex assembly. (It comes with loudspeaker and vibration motor )

    编辑

  10. Remove rear camera. Remove rear camera.

    • Remove rear camera.

    编辑

  11. Remove that securing bracket, then remove front camera. Remove that securing bracket, then remove front camera. Remove that securing bracket, then remove front camera.

    • Remove that securing bracket, then remove front camera.

    编辑

  12. Release connectors on the motherboard. Remove motherboard. Remove motherboard.

    • Release connectors on the motherboard.

    • Remove motherboard.

    编辑

  13. Remover cover bracket on the audio jack. Cut adhesive at the top of the audio jack and noise canceling mic, then remove it. Cut adhesive at the top of the audio jack and noise canceling mic, then remove it.

    • Remover cover bracket on the audio jack.

    • Cut adhesive at the top of the audio jack and noise canceling mic, then remove it.

    编辑

  14. This is audio jack flex coming with noise canceling mic.

    • This is audio jack flex coming with noise canceling mic.

    编辑

  15. Cut the adhesive underneath the earpiece and remove the earpiece. Cut the adhesive underneath the earpiece and remove the earpiece. Cut the adhesive underneath the earpiece and remove the earpiece.

    • Cut the adhesive underneath the earpiece and remove the earpiece.

    编辑

  16. Push the charging port flex out of the slot and remove it. Push the charging port flex out of the slot and remove it. Push the charging port flex out of the slot and remove it.

    • Push the charging port flex out of the slot and remove it.

    编辑

  17. Remove the microphone. Remove the microphone. Remove the microphone.

    • Remove the microphone.

    编辑

  18. Done.

    • Done.

    编辑

作者

与3其他贡献者

Lenka

于2015年11月06日注册

2,298 信誉积分

创作了6篇指南

徽章: 13

+ 10更多徽章

23条评论

添加一条评论

No Service after a tear down. What is the problem?

Yuhao Min - 回复

it is hard to define which part causes such problem. Make sure the signal antenna connects with logic board perfectly.

Witrigs -

Would the water proof go out because of the removal/teardown ?

Tam Alden - 回复

Most likely. The back is glued on so unless you can make that seal perfect again, the phone wont be water proof.

Discalimer: I don't own a z5 and have never taken one apart but I have dissasembled my z3 to replace the screen and they look very similar.

Kip K -

Hi Lenka,

short question was that a normal xperia z5 or the dual SIM Version because it looks like the SIM reader is long enough to Support two SIM cards. It would be nice if you could check if there are two SIM ports here.

Tobias K - 回复

添加评论

浏览统计数据:

过去的24小时： 22

过去的7天： 141

过去的30天： 657

总计 125,577