跳转到主内容

在此拆机指南中使用的工具

这个拆解是不是维修指南。 要维修你的的PlayStation Camera,请使用我们的维修手册

  1. There are two PH0 Screws in the socket which hold the cable. Unscrew two PH0 Screws and pull off the cable holder. Unscrew two PH0 Screws and pull off the cable holder.
    • There are two PH0 Screws in the socket which hold the cable.

    • Unscrew two PH0 Screws and pull off the cable holder.

  2. The next two PH0 Screws are located BEHIND the two polycarbonate-plates of the two camera-lenses. Take a sharp tweezer and stab under that plate. The plates are glued with a sticky tape to the housing. These plates are very fragile and will break if handled incautious. The next two PH0 Screws are located BEHIND the two polycarbonate-plates of the two camera-lenses. Take a sharp tweezer and stab under that plate. The plates are glued with a sticky tape to the housing. These plates are very fragile and will break if handled incautious. The next two PH0 Screws are located BEHIND the two polycarbonate-plates of the two camera-lenses. Take a sharp tweezer and stab under that plate. The plates are glued with a sticky tape to the housing. These plates are very fragile and will break if handled incautious.
    • The next two PH0 Screws are located BEHIND the two polycarbonate-plates of the two camera-lenses. Take a sharp tweezer and stab under that plate. The plates are glued with a sticky tape to the housing. These plates are very fragile and will break if handled incautious.

  3. There is one more PH0  screw to remove. This one is behind the other lens.
    • There is one more PH0 screw to remove. This one is behind the other lens.

    • This was the easy part.

  4. There are many clips in there. There are many clips in there. There are many clips in there.
    • There are many clips in there.

  5. Android 维修工具包

    一个新的屏幕或电池就在一个套件之内。

    现在开始购物

    Android 维修工具包

    一个新的屏幕或电池就在一个套件之内。

    现在开始购物
  6. Encore two photos where to locate these nasty clips Encore two photos where to locate these nasty clips
    • Encore two photos where to locate these nasty clips

  7. The other half of the housing is attached to a solid U-Frame with the electronics. There are four silver screws, PH0. Four microphones, two with black/yellow cables and two with black/red wiring.
    • The other half of the housing is attached to a solid U-Frame with the electronics.

    • There are four silver screws, PH0.

    • Four microphones, two with black/yellow cables and two with black/red wiring.

  8. The backside of the U-frame. The cable is not soldered, there is a plug. Detail of the plug.
    • The backside of the U-frame. The cable is not soldered, there is a plug.

    • Detail of the plug.

  9. 6 PH1 screws. Take a small magnet to hold them. 6 PH1 screws. Take a small magnet to hold them.
    • 6 PH1 screws. Take a small magnet to hold them.

  10. The connector of the mikrophone-array The connector of the mikrophone-array
    • The connector of the mikrophone-array

  11. The lenses, plastic, glued tight. NOT ADJUSTABLE. NOT ADJUSTABLE.
    • The lenses, plastic, glued tight.

    • NOT ADJUSTABLE.

  12. Backside, two small PH0 at each CCD. But the Cameramodules are clued to the board,too - without destruction, you can not open it. I want to save it as spare-part, so i don't want to open it. So here is finito capito. :) Thanks for watching...
    • Backside, two small PH0 at each CCD. But the Cameramodules are clued to the board,too - without destruction, you can not open it.

    • I want to save it as spare-part, so i don't want to open it. So here is finito capito. :) Thanks for watching...

  13. Extra: The wiring.
    • Extra: The wiring.

    • It's an USB3 cable without green/white Pimf. There are three SEPARATE ISOLATED metalfoil shields with wire, red-black-power and two Pimf yellow/blue and orange/green. So ja, thats it. Paulaner.

Schwarzstein

于2013年07月15日注册

2,385 信誉积分

创作了14篇指南

Only 7 steps? Where is the rest of the teardown? I wanted to see detailed images of the optics.

Alexandru Voda - 回复

Ja, okay, i made some pictures for you. The optics are in Step 10.

Enjoy.

Freundliche Grüsse. :)

Schwarzstein - 回复

Does anyone think it would be possible to cut the wires from two cameras and splice the wires together and put the power on a A/B rocker switch to switch between two cameras?

Dan Schultz - 回复

添加评论

浏览统计数据:

Past 24 Hours: 1

Past 7 Days: 7

Past 30 Days: 47

总计 7,993