在此拆机指南中的精选工具

简介

Here is the disassembly for a Nikon Coolpix 3200 digital camera.

这个拆解是不是维修指南。 要维修你的的Nikon Coolpix 3200,请使用我们的服务手册

Use a small Philips screwdriver to remove the screws from the base of the camera.
  • Use a small Philips screwdriver to remove the screws from the base of the camera.

添加评论

Use a small Philips screwdriver to remove the screws from the side of the camera where the computer lead is.
  • Use a small Philips screwdriver to remove the screws from the side of the camera where the computer lead is.

添加评论

  • Use a small Philips screwdriver to remove the two screws from the side of the camera where the card reader is.

添加评论

  • Pry apart the outer casing. A gray plastic threaded piece (used to attach camera to a tripod) will fall out.

添加评论

  • Use a Phillips screwdriver to remove the two silver screws that connect the circuit board to the outer front casing.

添加评论

  • Pry apart the front outer casing from the circuit board. The camera will now be in three pieces.

添加评论

  • Pull the connecting strip on the circuit board which connects it to the back outer casing.

添加评论

  • Use a Philips screwdriver to remove the two screws next to the computer port and the brass screw on the circuit board.

添加评论

  • Use a Phillips screwdriver to unscrew the three screws that connect the outer lens rim to the front casing.

添加评论

  • Use a Philips screwdriver to remove the three screws that hold the flash cover to the outer front casing.

添加评论

  • Open the lid of the battery compartment and use a Philips screwdriver to remove the two screws at the bottom.

添加评论

  • Use a Phillips screwdriver to unscrew the two screws that connect the inside battery casing to the front of the outer casing.

添加评论

  • Pull off the battery casing from the inside of the outer front casing. The circuit board, battery casing, and front outer casing will be attached by a connecting strip along with red and black wires.

添加评论

  • Use scissors to cut the red and black wires away from the battery points of contact.

添加评论

  • Pull the connecting strip away from the circuit board to separate it from the front casing.

添加评论

  • Use a Philips screwdriver to unscrew the two screws that connect the photo button to the outer front casing.

添加评论

  • Firmly press on the photo button and this component will pop out.

添加评论

  • Use a scalpel to pry apart the metal inner part of the button from the plastic outer piece.

添加评论

  • Use your fingernails to peel the outer rim from the front casing.

添加评论

  • Pull the connecting strip out of the circuit board to separate it from the LCD screen.

添加评论

  • Use your fingernails to pry apart the back metal piece of the screen (covered by a black plastic film) from the front section of the screen.

添加评论

  • Pry apart the back black piece and front white piece of the screen. Inside the screen there are four sheets of plastic: one opaque, two mirrored, and one thicker plastic sheet which has a foil piece attached to it.

添加评论

  • Use a hammer and chisel to separate the lens piece of the camera from the circuit board.

添加评论

  • Use your fingernails to pry off the motor, motor cover, and flash piece from the lens piece of the camera.

添加评论

Milly Whitehead

于2010年03月09日注册

47 信誉积分

撰写一个指南

Oh, and then just do everything in reverse to put it back together again? That hammer and chisel bit bothers me a bit.

mrs_prolo - 回复

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 4

过去的30天: 12

总计 4,989