跳转到主内容

修复你的物品

维修的权力

配件 & 工具

在此拆机指南中使用的工具

这个拆解是不是维修指南。 要维修你的的Nikon 1 J5,请使用我们的维修手册

  1. Remove Lens, MicroSD Card and Battery Remove Lens, MicroSD Card and Battery
    • Remove Lens, MicroSD Card and Battery

  2. Remove 2 screws first Lift the cover Disconnect LCD FPC
    • Remove 2 screws first

    • Lift the cover

    • Disconnect LCD FPC

    • Then remove 4 screws

    • Remove LCD assembly

  3. Insert wisdom here. Insert wisdom here.
    • Insert wisdom here.

  4. Remove 2 screws
    • Remove 2 screws

  5. Open connection bay
    • Open connection bay

    • Remove 2 screws

  6. Remove 1 screw under the DC power cable notch cover
    • Remove 1 screw under the DC power cable notch cover

  7. Remove 4 screws and be ware the length difference Peel the rubber open from right hand side Remove 1 screw
    • Remove 4 screws and be ware the length difference

    • Peel the rubber open from right hand side

    • Remove 1 screw

  8. Now the back case can be removed. There's no fragile FPC or cables in this step. Just be patient.
    • Now the back case can be removed.

    • There's no fragile FPC or cables in this step. Just be patient.

  9. 任天堂 Switch 套装

    快速恢复到游戏的状态

    购买 Switch 套装

    任天堂 Switch 套装

    快速恢复到游戏的状态

    购买 Switch 套装
  10. Disconnect speaker cable Pull out keypad cable Pull out keypad cable
    • Disconnect speaker cable

    • Pull out keypad cable

  11. Insert small crowbar or flat head screw driver here to lift the keypad up. Those clips are very tight.
    • Insert small crowbar or flat head screw driver here to lift the keypad up.

    • Those clips are very tight.

  12. Remove 3 screws Remove 2 screws Notice the sizes of screws
    • Remove 3 screws

    • Remove 2 screws

    • Notice the sizes of screws

  13. Need some tape peeling
    • Need some tape peeling

  14. Dangerous DC Voltage > 200V
    • Dangerous DC Voltage > 200V

    • Use 10kohm, >2W resistor, connect Brown and Blue point for more than 10sec.

    • DMM's Low-Z voltage works even better.

    • Measure voltage between 3 points to ensure voltage <10V

  15. Detach every FPC you can find Detach every FPC you can find Detach every FPC you can find
    • Detach every FPC you can find

  16. Detach every FPC you can find Detach every FPC you can find Detach every FPC you can find
    • Detach every FPC you can find

  17. Desolder Power FPC and Flash cables Desolder Power FPC and Flash cables Desolder Power FPC and Flash cables
    • Desolder Power FPC and Flash cables

  18. More FPC More FPC
    • More FPC

  19. Lift Main PCB, SLOWLY and GENTLY One more FPC at the back side. One more FPC at the back side.
    • Lift Main PCB, SLOWLY and GENTLY

    • One more FPC at the back side.

  20. Insert wisdom here. Insert wisdom here.
    • Insert wisdom here.

  21. Mark 3 screws for their ID and position. Also record how many turns to the limit.
    • Mark 3 screws for their ID and position.

    • Also record how many turns to the limit.

    • Measure and record distance to front flange if possible.

    • These screws will affect focus focal plain.

  22. Sensor module and IR-cut filter Sensor module and IR-cut filter Sensor module and IR-cut filter
    • Sensor module and IR-cut filter

  23. Insert wisdom here. Insert wisdom here. Insert wisdom here.
    • Insert wisdom here.

  24. And I don't quite remember what is this filter/window. And I don't quite remember what is this filter/window. And I don't quite remember what is this filter/window.
    • And I don't quite remember what is this filter/window.

    • More steps coming soon. Power switch, mode switch, main wheel, shutter button(DIY cable release)

    • Some soldering/de-soldering work needed to remove/replace the main PCB

Terrance

于2009年11月17日注册

4,613 信誉积分

创作了6篇指南

Hi Terrance - the return spring on the on/off switch has gone on mine - are you able to see how to get at this on your stripped down one?

freecycle at evendine dot eclipse dot co dot uk in case I don’t notice it coming up here

chris morton - 回复

hmm, haven’t dug that deep yet… The front case disassembly seems very tricky. Also the IR-cut removal.

Terrance -

Sorry to hear that, I arrive here coming for a solution for the return spring on the on/off switch, is not a big problem but a pain and battery drain if you don’t realise :)

Anyway thanks for your teardown really formative.

juan valderrabano - 回复

I tried to remove the top cover to repair the return spring on the ON/OFF, but I was not able to separate it from the body. I have no solution.

Jacques Guyon - 回复

Appended some steps about the sensor. In case you’re interested.

Terrance - 回复

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 5

过去的30天: 38

总计 847